-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without turning off the power. Show Detail
- No：1367
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
The existing MICREX-F program does not need any modification. Show Detail
- No：1319
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Ethernet module. After replacing an Eth... Show Detail
- No：1590
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
On the positioning module (Type_NP1F-MP2/MA2), the 'ERR' LED turns ON. What are the possible causes?
A possible cause is that a “Deviation amount over error” occurred. For details, refer to the user's manual FEH213 (NP1F-MA2) or FEH214 (NP1F-MP2) 'Section 8 ... Show Detail
- No：1290
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Common memory 1 and common memory 2 are handled together in terms of timing. However, to maintain the uniqueness of data including those in common memory 1 a... Show Detail
- No：1311
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Is it permitted to have an unused slot in an SPH system configuration?
An unused slot is permitted in a system configuration. If you plan to mount a module in the unused slot in the future, it can be registered as 'unimplemen... Show Detail
- No：1313
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:32
- Category： Main unit
-
Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with ports 1 to 8. With ports 9 to 32, pu... Show Detail
- No：1321
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
-
The P-link memory is prepared in the P-link module. It is separate from the memory in the CPU and no change takes place at the time of switchover to a standb... Show Detail
- No：1343
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
It takes place only when data are received from an external device. Show Detail
- No：1400
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
They are retained. Note, however, that they are cleared if the power of the FL-net module is turned off. Show Detail
- No：1405
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
1-10 of Total 398