-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I have configured a multi-CPU system, but the system has run out of memory for the multi-CPU. Can I access the common general memory from the other...
- What is the rated current value of the fuse in the power supply module (NP1S-22)? I want to know to select the circuit breaker on the primary side ...
- When I mount the user ROM card for the SPH200 (Type_ NP8PMF-16) without changing its write protection from OFF, is the content of the ROM protected?
- When the retain memory (memory for data backup with a battery) of the CPU module of the MICREX-SX Series SPH is corrupted, how does the CPU module ...
- Can I mount or remove a CPU module and a power supply module on a hot plug base board while the system power is on?
GLOBAL
Search by category
Keyword Search
FAQ within [ Main unit ]
-
What is the difference between the LG and FG terminals of the power supply module (Type_ NP1S-22)?
The LG terminal is a line filter ground terminal in the power supply module. It is intended for guiding any external noise produced in the power supply or sw... Show Detail
- No：1374
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 10:52
-
When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition. If the power is reset again in this... Show Detail
- No：1611
- Displayed Date：2023/04/25 19:00
-
Can I store multiple programs in the user ROM card (CF or SD) ?
No, it is not possible. Only one program can be stored. Show Detail
- No：1298
- Displayed Date：2023/04/25 19:00
-
You can mount or remove a CPU module during system operation, but not a power supply module. [Related document] For the details of hot plugging function, r... Show Detail
- No：1600
- Displayed Date：2023/04/25 19:00
-
You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the system definition of the loader designed f... Show Detail
- No：1531
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:50
-
The equivalent data is retained for one default task during switching and the standby CPU starts execution from the beginning of the task. Show Detail
- No：1530
- Displayed Date：2023/04/25 19:00
-
Is there an RAS that detects an error of the external power supply used for an I/O module?
No, there isn't. Receive the external power supply as an external input to detect the status. Show Detail
- No：1388
- Displayed Date：2023/04/25 19:00
-
You cannot access general memory other than the memory for the multi-CPU from the other CPU. Access using the direct read/write FB is used for the access to ... Show Detail
- No：1645
- Displayed Date：2023/04/25 19:00
-
The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment, connect the cable to the IN (input)... Show Detail
- No：1535
- Displayed Date：2023/04/25 19:00
-
No, it doesn't. A power supply module may occupy two slots (Type_ NP1S-22, NP1S-42) or one slot (Type_ NP1S-81, NP1S-91). The connector at the far left... Show Detail
- No：1340
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:34
1-10 of Total 34