When you use preset operation in the linear operation mode, counting is sometimes discontinued due to preset overflow.

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated.

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without p

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding.

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

The high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) cannot be mounted on the T

The minimum required products are (1) High-performance CPU exclusively for the electronic cam, (2) pulse train combine

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by d

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

1-10 of Total 50

≪ 1 / 5page ≫

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...

When you use preset operation in the linear operation mode, counting is sometimes discontinued due to preset overflow. Show Detail
- No：1675
- Displayed Date：2023/04/25 19:00
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated. (3) The preset command is given aft... Show Detail
- No：1640
- Displayed Date：2023/04/25 19:00
With the high-speed output module (Type_ NP1Y32T09P1-A), the LED flashes but no pulse is output to the outside. What should I check?

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated. If no pulse output is generated in t... Show Detail
- No：1291
- Displayed Date：2023/04/25 19:00
What is the difference between the PID forward and backward operations when the PID FB package is used?

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without processing it (as-is)_ and (2) the for... Show Detail
- No：1625
- Displayed Date：2023/04/25 19:00
How do I use a manual pulse generator with the positioning module (Type_NP1F-MP2/MA2)?

Set the I/O area of the positioning module following the steps below. 1) Set 'h1C00' in the offset word address +16 (Ch1 Set value area: Low word). (Set ... Show Detail
- No：1396
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:17
What measures can I take against external noise of the high-speed counter (Type_ NP1F-HC2)?

Use the recommended shielded twisted pair cable mentioned in the User's Manual. Also provide shielding. Show Detail
- No：1365
- Displayed Date：2023/04/25 19:00
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
Can I mount the high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) on the T-link expansion (RT1)?

The high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) cannot be mounted on the T-link expansion (RT1). Show Detail
- No：1433
- Displayed Date：2023/04/25 19:00
Which devices are required for controlling an electronic cam with the SPH Series? What should I prepare?

The minimum required products are (1) High-performance CPU exclusively for the electronic cam, (2) pulse train combined module (Type_ NP1F-MP2) or anal... Show Detail
- No：1323
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:20
How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59