-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition. If the power is reset again in this... Show Detail
- No：1611
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
Access the 'Programmable Controllers MICREX-SX Series' page in the Fuji Electric website, and click the 'Loader software' tab in 'PLC What's New.' You can d... Show Detail
- No：1499
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'no equipment.' If the input specified... Show Detail
- No：1658
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:04
- Category： Support tool (Standard)
-
Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated. (3) The preset command is given aft... Show Detail
- No：1640
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The D300win cannot connect to the SX via the Ethernet module.
The IP address of the Ethernet module will become effective when the power supply is turned off once and then turned on again after the module driver is dow... Show Detail
- No：1434
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
Is it possible to indirectly specify the timer set value with the Standard Loader (Type_ NP4H-SWN)?
Yes, it is possible. Input a memory address (DLxx) instead of an immediate value as the operand of the timer instruction. Show Detail
- No：1407
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected. (2) The Z-phase/timing input signal f... Show Detail
- No：1399
- Displayed Date：2023/04/25 19:00
- Category： Function
-
You can install a T-link master (processor part in the case of MICREX-F series) at any position on the T-link transmission line. Show Detail
- No：1280
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
-
No, it is not necessary for normal operation. The main purposes of mounting a CF card or an SD card on a CPU module are as follows. - You can write a progr... Show Detail
- No：1474
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:31
- Category： Main unit
-
When station number '0' is set on the servo, the station number set on the loader becomes effective. If, however, you want to use the servo for fail-soft st... Show Detail
- No：1594
- Displayed Date：2023/04/25 19:00
- Category： Others
71-80 of Total 398