There are two ways to connect a USB port of a personal computer and a CPU: 1) Connect to the USB port of the CPU (direc

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the p

When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition

It is the same as the loader mode (mode switch 3) of the general-purpose communication module (Type_ NP1L-RS1/RS2/RS3/RS

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need

You can display the mismatch circuit in the program and differences using the 'Compare Projects' command of the Expert

You can mount or remove a CPU module during system operation, but not a power supply module. [Related document] For th

The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the sys

Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with inde

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'n

Search by category

Keyword Search

FAQ within [ PLC ]

61-70 of Total 398

≪ 7 / 40page ≫

I have connected the SX series CPU and the loader PC via USB. I have installed the USB driver and configured the communication settings, but commun...

There are two ways to connect a USB port of a personal computer and a CPU: 1) Connect to the USB port of the CPU (directly connected to the USB cable). 2) ... Show Detail
- No：1654
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:03
- Category： Support tool
Is the backup battery consumed while the control power supply of the CPU is active?

The backup battery is intended to back up the data memory (SRAM) inside of the CPU. While the system is turned on, the power is supplied from the control pow... Show Detail
- No：1621
- Displayed Date：2023/04/25 19:00
- Category： Accessory
When the retain memory (memory for data backup with a battery) of the CPU module of the MICREX-SX Series SPH is corrupted, how does the CPU module ...

When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition. If the power is reset again in this... Show Detail
- No：1611
- Displayed Date：2023/04/25 19:00
- Category： Main unit
What is the communication protocol for the loader port of the CPU module of the MICREX-SX SPH Series?

It is the same as the loader mode (mode switch 3) of the general-purpose communication module (Type_ NP1L-RS1/RS2/RS3/RS4/RS5). Show Detail
- No：1379
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
When I change a program online (patch POU), error message shown 'The resevation area of the non-retain memory of POU xxx is short (2 word).' Why?

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need to stop the CPU. Please consider the... Show Detail
- No：1661
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:05
- Category： Support tool (D300win)
When comparing the project in CPU with that in the personal computer by Expert loader, a mismatch between the programs was detected. How can I find...

You can display the mismatch circuit in the program and differences using the 'Compare Projects' command of the Expert loader. For the operating procedure, ... Show Detail
- No：1663
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
Can I mount or remove a CPU module and a power supply module on a hot plug base board while the system power is on?

You can mount or remove a CPU module during system operation, but not a power supply module. [Related document] For the details of hot plugging function, r... Show Detail
- No：1600
- Displayed Date：2023/04/25 19:00
- Category： Main unit
A nonfatal fault of the takt cycle monitoring error has occurred. What is a possible cause?

The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the system definition is shorter than the ac... Show Detail
- No：1576
- Displayed Date：2023/04/25 19:00
- Category： Error
How can I change the CPU type in an already created project?

Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with index 'o' or later). Show Detail
- No：1467
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
To debug a PLC program without I/O module, I set I/Os as 'no equipment'. Then, I tried to set input contact (X) using switch of MONITOUCH. However,...

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'no equipment.' If the input specified... Show Detail
- No：1658
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:04
- Category： Support tool (Standard)