-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
You can display the mismatch circuit in the program and differences using the 'Compare Projects' command of the Expert loader. For the operating procedure, ... Show Detail
- No：1663
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
A nonfatal fault of the takt cycle monitoring error has occurred. What is a possible cause?
The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the system definition is shorter than the ac... Show Detail
- No：1576
- Displayed Date：2023/04/25 19:00
- Category： Error
-
What is necessary for MODBUS_TCP communication between SPH and an external device?
The following are necessary. 1) Hardware Ethernet interface module (NP1L-ET1) or CPU module with built-in Ethernet (SPH2000/3000 series CPU types w... Show Detail
- No：1470
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:30
- Category： Communication (Ethernet)
-
After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software offset setting will be disabled. Show Detail
- No：1667
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
There is a difference between 'Unpassive' and 'Fullpasisve' as follows. 1) Unpassive: Communicates with a device that has any IP or port No. 2) Fullpassi... Show Detail
- No：1630
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:01
- Category： Communication (Ethernet)
-
Yes, it is the same as in the SPH series (except for SPH3000MM). Show Detail
- No：1516
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
With the SPH Series, the memory boundaries between the non-retain, retain, system FB and user FB memory areas can be changed to change the size of the respec... Show Detail
- No：1359
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
The product type without 'RI' judges ON/OFF of the inputs by current. On the other hand, the product type with 'RI' judges ON/OFF of the inputs by voltage. ... Show Detail
- No：1650
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
I cannot download a project to the user ROM card inserted in the CPU. What is a possible cause?
This problem is probably caused by the following reasons: [For SPH300/2000/3000 series] 1) The CPU mode selection switch is not set at the 'UROM-TERM' pos... Show Detail
- No：1528
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:47
- Category： Support tool
-
You cannot upgrade 'MICREX-F PLC Programmer' free of change. 'MICREX-F PLC Programmer' that can be installed as NL4N-WNSB is currently included with the p... Show Detail
- No：1455
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 09:36
- Category： Support tool (Others)
31-40 of Total 398