-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
In the system definition, group-type slave stations in any I/O configuration are registered as 'DeviceNet capsule.' In addition, the numbers of input and out... Show Detail
- No：1644
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
You cannot upgrade 'MICREX-F PLC Programmer' free of change. 'MICREX-F PLC Programmer' that can be installed as NL4N-WNSB is currently included with the p... Show Detail
- No：1455
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 09:36
- Category： Support tool (Others)
-
No, you cannot access the input (output) parameter (WV*, DV*) for which the data length is set in words/ double-words by using a bit address within the user ... Show Detail
- No：1677
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosis' dialog, check the 'Resource inform... Show Detail
- No：1671
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
When you use preset operation in the linear operation mode, counting is sometimes discontinued due to preset overflow. Show Detail
- No：1675
- Displayed Date：2023/04/25 19:00
- Category： Function
-
This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board. Show Detail
- No：1335
- Displayed Date：2023/04/25 19:00
- Category： Error
-
What is the meaning of EN and ENO of functions in Expert (D300win)?
The EN and ENO terminals of functions mean the start operation terminal and the operation result terminal, respectively. ・When the variable connected to the... Show Detail
- No：1476
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:31
- Category： Support tool (D300win)
-
Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need to stop the CPU. Please consider the... Show Detail
- No：1661
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:05
- Category： Support tool (D300win)
-
You don't need a dedicated cable. Since the parameters will be set via the CPU module, you need a loader cable for the PLC and the program loader software. Show Detail
- No：1676
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
I use the Ethernet module (Type_NP1L-ET1). Is the IP address assigned automatically?
The IP address is not assigned automatically. (DHCP function is not supported.) The default IP address is '192.168.0.1'. You can check the IP address b... Show Detail
- No：1595
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
371-380 of Total 398