-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
How can I change the CPU type in an already created project?
Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with index 'o' or later). Show Detail
- No：1467
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
The MICREX-SX series positioning module 'Type_NP1F-HD2A' replaces NC1F-VP1/FGU130B. Be aware of the following points: 1) NP1F-HD2A is differential output t... Show Detail
- No：1463
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported. Show Detail
- No：1442
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in the built-in memory (RAM) of the P/PE-l... Show Detail
- No：1436
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Since the conversion accuracy after a scaling change remains within the specifications, rescaling is unnecessary. Show Detail
- No：1430
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
I want to relay the SX bus optical cable. Is it possible?
Yes, it is possible. Note that one relay causes attenuation of about 1 dB. The allowable attenuation is 7 dB in total. Careful consideration is required be... Show Detail
- No：1429
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
When SX-Programmer Expert (D300win) was upgraded to V3.3.2.0, the 'IP address and gateway setting definition' was added to accommodate the function addition ... Show Detail
- No：1417
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
Is broadcast communication via Ethernet possible?
It is possible as long as the protocol is UDP/IP. In the M_OPEN FB, specify 255.255.255.255 as the IP address to be set for the 'communication destination s... Show Detail
- No：1415
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
It takes place only when data are received from an external device. Show Detail
- No：1400
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The Control Utility only supports the COM port and USB port and cannot be used. Show Detail
- No：1397
- Displayed Date：2023/04/25 19:00
- Category： Support tool
341-350 of Total 398