With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of

No, you cannot use NW0H-CNV. The RS-232C/422 converter for personal computer loaders (Type_NW0H-CNV) needs to be supplie

To enable the 'output value reference input,' the output module must be actually mounted. If the output module is set as

Once an error history is generated, it is retained internally within the FL-net module and is cleared when the power is

The product type without 'RI' judges ON/OFF of the inputs by current. On the other hand, the product type with 'RI' jud

The MICREX-SX is assumed to be installed inside a dustproof type switchboard in a general factory. The amount of dust m

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated

No, you do not have to connect T-link devices in ascending order of address. In addition, you can assign addresses at s

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors

Yes, there are. When you install an expansion FB, sample programs are installed as a compressed project (extension *.Zp

Search by category

Keyword Search

FAQ within [ PLC ]

321-330 of Total 398

≪ 33 / 40page ≫

What is the range of IP addresses that can be used for FL-net?

With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of *_ 1 to 254) Show Detail
- No：1301
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:19
- Category： Communication (Others)
The loader connector of SPH series CPU modules has been changed into RJ45 connector. Can I use an RS-232C/422 converter for personal computer loade...

No, you cannot use NW0H-CNV. The RS-232C/422 converter for personal computer loaders (Type_NW0H-CNV) needs to be supplied power from the PLC side, however, t... Show Detail
- No：1529
- Displayed Date：2023/04/25 19:00
- Category： Support tool
In a multi-CPU system, I set the 'Output reference input' of the I/O group registration but the variable (contact) specified for the output referen...

To enable the 'output value reference input,' the output module must be actually mounted. If the output module is set as 'unimplemented' in the system config... Show Detail
- No：1637
- Displayed Date：2023/04/25 19:00
- Category： Application
How does the FL-net module (Type_ NP1L-FL1/FL2/FL3) clear the error history recorded in each memory?

Once an error history is generated, it is retained internally within the FL-net module and is cleared when the power is turned off and turned on again or whe... Show Detail
- No：1567
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
There are two types of AC input modules, for 100V (NP1X1610, NP1X1610-RI) and 200V (NP1X1611, NP1X1611-RI). What is the difference between the prod...

The product type without 'RI' judges ON/OFF of the inputs by current. On the other hand, the product type with 'RI' judges ON/OFF of the inputs by voltage. ... Show Detail
- No：1650
- Displayed Date：2023/04/25 19:00
- Category： I/O
The physical environmental conditions of the MICREX-SX specify 'Pollution degree 2.' Please specifically explain this environment.

The MICREX-SX is assumed to be installed inside a dustproof type switchboard in a general factory. The amount of dust mentioned above is assumed to cause no... Show Detail
- No：1406
- Displayed Date：2023/04/25 19:00
- Category： Others
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated. (3) The preset command is given aft... Show Detail
- No：1640
- Displayed Date：2023/04/25 19:00
- Category： Function
Do I have to connect T-link devices (slave stations) connected to T-link in ascending order of address?

No, you do not have to connect T-link devices in ascending order of address. In addition, you can assign addresses at some intervals for the future expans... Show Detail
- No：1279
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:15
- Category： Communication (T-link)
I don't have the SX bus loop-back plug (Type_ NP8B-BP). Can I use the SX bus cable instead?

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors at both ends of the cable to IN and ... Show Detail
- No：1543
- Displayed Date：2023/04/25 19:00
- Category： Accessory
Are there any sample programs of various expansion FBs such as general-purpose communication that can be used for the Standard Loader (Type_ NP4H-S...

Yes, there are. When you install an expansion FB, sample programs are installed as a compressed project (extension *.Zpj) in a folder named 'SAMPLES' under... Show Detail
- No：1558
- Displayed Date：2023/04/25 19:00
- Category： Application