Fuji Electric website provides information on the standards that the MICREX-SX series complies with. Visit the following

The base board that plays the role of a hub of optical converter modules is not represented in the system definitions.

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in

No, it is not possible. Combine the electronic cam FB package (Type_ NP4N-CAMFV3) with a positioning control module (Typ

It is possible by preparing two types of power supply for driving the transistor device and the load. Refer to the User

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a lin

The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are s

The print scaling setting can be configured by using the page layout editor. The LD language and other graphical elemen

You can install only the USB driver afterwards. For V3.6.12.18 or later version of D300win, the USB driver can be insta

The data written with the F_WRITE FB is in a binary format. Consequently, it can be manipulated with commercial binary e

Search by category

Keyword Search

FAQ within [ PLC ]

311-320 of Total 398

≪ 32 / 40page ≫

What standards does the MICREX-SX series comply with?

Fuji Electric website provides information on the standards that the MICREX-SX series complies with. Visit the following URL. Show Detail
- No：1358
- Displayed Date：2023/04/25 19:00
- Category： Others
Is there anything I should take note of when using an optical converter module (Type_ NP1L-OL1/OL2) as a hub on one base board?

The base board that plays the role of a hub of optical converter modules is not represented in the system definitions. When the power supply (PS) of the sam... Show Detail
- No：1351
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
With the DeviceNet master module (Type_ NP1L-DN1), how can I create a scan list and register it with the master module?

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in the system configuration definitions... Show Detail
- No：1346
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:35
- Category： Communication (Others)
Is electronic cam operation possible without using the dedicated module?

No, it is not possible. Combine the electronic cam FB package (Type_ NP4N-CAMFV3) with a positioning control module (Type_ NP1F-MP2/MA2). Show Detail
- No：1334
- Displayed Date：2023/04/25 19:00
- Category： Function
Is it possible to use a transistor output module (12 to 24 V DC model) of the SPH Series at a load voltage lower than the rated voltage?

It is possible by preparing two types of power supply for driving the transistor device and the load. Refer to the User's Guide, which provides explanatio... Show Detail
- No：1331
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:32
- Category： I/O
Is it possible to use the optical converter NP1L-OL1 between processors as with the P-link?

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a link between processors. Show Detail
- No：1327
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
- Category： Communication (Others)
With a positioning control module (Type_ NP1F-MP2/MA2), what are the statuses of the status information signals after power-up?

The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are set to [1]. The interrupt input sig... Show Detail
- No：1318
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
With the print function of D300win, the printed characters are too small. How can I make them bigger?

The print scaling setting can be configured by using the page layout editor. The LD language and other graphical elements can be enlarged by zooming into ... Show Detail
- No：1286
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:16
- Category： Support tool (D300win)
When the USB driver is not installed in D300win, can I install only the USB driver afterwards, or do I have to re-install the D300win system?

You can install only the USB driver afterwards. For V3.6.12.18 or later version of D300win, the USB driver can be installed at the time of installation of... Show Detail
- No：1285
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:16
- Category： Support tool (D300win)
Is it possible to use a PC application program to manipulate data that was written with the SX application (F_WRITE) onto the memory card inserted ...

The data written with the F_WRITE FB is in a binary format. Consequently, it can be manipulated with commercial binary editors. Show Detail
- No：1623
- Displayed Date：2023/04/25 19:00
- Category： Application