In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'n

In exponentiation operation, when a negative value is used for the base, the result is 0.

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a com

After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software off

The MICREX-SX series T-link also has the fail-soft operation function, but not the general fail-soft function. In MICR

Yes, you can. The SXPLC simulation function is supported by V3.0.14 or later version of Expert (D300win). Use the SXP

The addresses of structure data are automatically assigned by the D300win to ensure optimum memory assignment. Data sam

This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed c

_F_WRITE_CSV_DINT' may be influenced by the file search time depending on the number of files in the CF. The time it ta

The Standard loader has two types of timer devices created in projects： local timers (T0 to 8191) that are only valid i

Search by category

Keyword Search

FAQ within [ PLC ]

311-320 of Total 398

≪ 32 / 40page ≫

To debug a PLC program without I/O module, I set I/Os as 'no equipment'. Then, I tried to set input contact (X) using switch of MONITOUCH. However,...

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'no equipment.' If the input specified... Show Detail
- No：1658
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:04
- Category： Support tool (Standard)
In ST language, when I use a negative value for the base of exponentiation (such as -2.0**4.0), the calculation result is different from the case w...

In exponentiation operation, when a negative value is used for the base, the result is 0. Show Detail
- No：1551
- Displayed Date：2023/04/25 19:00
- Category： Application
Can I use a commercial LAN cable for the SX bus instead of the dedicated cable?

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a commercial LAN cable (cross), the dedica... Show Detail
- No：1557
- Displayed Date：2023/04/25 19:00
- Category： Accessory
When I set offset on the analog module (NP1AXH8I-MR) by using software (parameters) and disable the software offset setting by operating hardware (...

After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software offset setting will be disabled. Show Detail
- No：1667
- Displayed Date：2023/04/25 19:00
- Category： I/O
The MICREX-F series T-link has the fail-soft function. Does the MICREX-SX series T-link have the same function?

The MICREX-SX series T-link also has the fail-soft operation function, but not the general fail-soft function. In MICREX-SX, fail-soft operation can be ind... Show Detail
- No：1479
- Displayed Date：2023/04/25 19:00
- Category： Function
Can I perform an offline simulation of a project created in Expert (D300win) and screen data of MONITOUCH?

Yes, you can. The SXPLC simulation function is supported by V3.0.14 or later version of Expert (D300win). Use the SXPLC simulator and SOFT MONITOUCH TE... Show Detail
- No：1512
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
When I perform data sampling on the structure data of the SPH (INT and DINT types mixed) from the UG, the data is assigned improperly from some mid...

The addresses of structure data are automatically assigned by the D300win to ensure optimum memory assignment. Data sampling is a method to acquire a certai... Show Detail
- No：1552
- Displayed Date：2023/04/25 19:00
- Category： Others
I have connected the SPH Series with the POD (UG Series) via the T-link. A code F8 is displayed on the screen of the POD. What is a possible cause?

This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed contact on the POD (UG), (3) Improp... Show Detail
- No：1559
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
The '_F_WRITE_CSV_DINT' FB allows a CSV file to be output to the memory card. How frequently can data be written? Is there any specific data of the...

_F_WRITE_CSV_DINT' may be influenced by the file search time depending on the number of files in the CF. The time it takes for 100 (200-word) DINT data to b... Show Detail
- No：1634
- Displayed Date：2023/04/25 19:00
- Category： Application
I use the timer T0 in the Standard loader. When I add a contact T0 to another POU and then execute program conversion, an error message appears say...

The Standard loader has two types of timer devices created in projects： local timers (T0 to 8191) that are only valid in the POU and global timers (T8192 to... Show Detail
- No：1652
- Displayed Date：2023/04/25 19:00
- Category： Application

311-320 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News