The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported.

Move to the item ID without using the access path on the client side (D_).

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have eith

In the parameter setting of the Ethernet module in the system definition, set the 'Server FTP command watch timer value'

For the Standard loader V2, you cannot specify array data for the operand that specifies the first address. (An error is

You can install a T-link master (processor part in the case of MICREX-F series) at any position on the T-link transmissi

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a com

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'n

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected.

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side.

Search by category

Keyword Search

FAQ within [ PLC ]

301-310 of Total 398

≪ 31 / 40page ≫

I use the Ethernet module (Type_ NP1L-ET1/ET2) in the Loader command mode. Can I also use the UDP/IP communication?

The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported. Show Detail
- No：1442
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
When I use the SX communication middleware (Type_ NP4N-MDLW) and specify (_) in the access path during the item registration for the client, Errno=...

Move to the item ID without using the access path on the client side (D_). Show Detail
- No：1556
- Displayed Date：2023/04/25 19:00
- Category： Support tool
For 1-to-1 communication of Ethernet, can I establish communication only using a LAN cable (cross cable), without using a hub?

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have either of the following specifications. ... Show Detail
- No：1582
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:55
- Category： Communication (Ethernet)
During loader command communication of Ethernet, a port is closed after it has not been accessed from a personal computer for a certain period of t...

In the parameter setting of the Ethernet module in the system definition, set the 'Server FTP command watch timer value' to 0. The port is not closed even if... Show Detail
- No：1612
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
- Category： Communication (Ethernet)
When I defined array (example WL990[WL0]) as start addoress of FMOVE in StandardV2 loader, error was detected by error check. Why?

For the Standard loader V2, you cannot specify array data for the operand that specifies the first address. (An error is detected during the program check.) ... Show Detail
- No：1665
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
When connecting devices on T-link, do I have to install a T-link master at the starting point (either end) of the connection configuration?

You can install a T-link master (processor part in the case of MICREX-F series) at any position on the T-link transmission line. Show Detail
- No：1280
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
Can I use a commercial LAN cable for the SX bus instead of the dedicated cable?

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a commercial LAN cable (cross), the dedica... Show Detail
- No：1557
- Displayed Date：2023/04/25 19:00
- Category： Accessory
To debug a PLC program without I/O module, I set I/Os as 'no equipment'. Then, I tried to set input contact (X) using switch of MONITOUCH. However,...

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'no equipment.' If the input specified... Show Detail
- No：1658
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:04
- Category： Support tool (Standard)
I want to run an external device by pulse output with the high-speed output module (Type_ NP1Y32T09P1-A). What are the points to note regarding the...

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected. (2) The Z-phase/timing input signal f... Show Detail
- No：1399
- Displayed Date：2023/04/25 19:00
- Category： Function
Can I upload a definition file downloaded from a configurator to NP1L-PD1/PD2?

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side. Show Detail
- No：1468
- Displayed Date：2023/04/25 19:00
- Category： Support tool

301-310 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News