-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
The temperature measurement value of the resistance temperature sensor (PT input) is unstable.
If this is caused by a fluctuation in the input temperature, moving average processing shown below may improve the condition. 1) Change the digital filter v... Show Detail
- No：1586
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:56
- Category： I/O
-
No, you cannot use NW0H-CNV. The RS-232C/422 converter for personal computer loaders (Type_NW0H-CNV) needs to be supplied power from the PLC side, however, t... Show Detail
- No：1529
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
If you start multiple Expert loaders (max. 2) earlier than V3.6.7, the one started later always goes into reference mode, which you cannot exit. To edit mu... Show Detail
- No：1498
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
Can I use a commercially available hub for FL-net modules?
We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of use for FL-net. * What is 'B.S'?... Show Detail
- No：1465
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:28
- Category： Communication (Others)
-
Timers of small numbers (T0 to T8191) are local timers (timers effective within the program only). To create timers that are effective in other programs (g... Show Detail
- No：1437
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
The number of M_OPEN FBs that can be opened simultaneously is limited to 56. The number of FBs that can be simultaneously opened for each module depends on t... Show Detail
- No：1435
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Up to 127 levels of nesting is possible. Show Detail
- No：1431
- Displayed Date：2023/04/25 19:00
- Category： Application
-
Check the feedback pulse wiring (to make sure that a shielded twisted pair is used, wiring conditions are appropriate, etc.). One possible reason for the c... Show Detail
- No：1421
- Displayed Date：2023/04/25 19:00
- Category： Function
-
With a general-purpose communication module, is RS232C completely full duplex?
It is full duplex for both hardware and software (firmware) for anything other than communication by M_RECEIVE and M_SEND on the SX bus, which are FB interna... Show Detail
- No：1413
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Is there an RAS that detects an error of the external power supply used for an I/O module?
No, there isn't. Receive the external power supply as an external input to detect the status. Show Detail
- No：1388
- Displayed Date：2023/04/25 19:00
- Category： Main unit
291-300 of Total 398