-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
No, you cannot. Use NW0H-CNV (RS-232C/RS-422 converter) or NP4H-CVU (USB/RS-422 converter) in combination with NW0H-CA3 Show Detail
- No：1303
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
In a CPU redundant system, how can I update a program while the system is running?
Refer to the following How-to Guide, which describes how to update a program while a redundant system is running. MICREX SX How-to Guide 'How to Change Prog... Show Detail
- No：1352
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
Please tell me how to register a T-link model of UG (or V Series) as a POD in the system definition.
Select a T-link capsule and set the numbers of input/output words. By default, a POD requires one word for input and one word for output. Show Detail
- No：1438
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
Is the programming support tool for MICREX-F series (MICREX-F PLC Programmer) still available?
Yes, it is. Ordering code: NP4H-SWN (The loader software for MICREX-F is included in the product CD together with the loader software for MICREX-SX.) Show Detail
- No：1453
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Others)
-
Access the 'Programmable Controllers MICREX-SX Series' page in the Fuji Electric website, and click the 'Loader software' tab in 'PLC What's New.' You can d... Show Detail
- No：1499
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
No, they do not have polarity because they use relay contacts. Show Detail
- No：1585
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
Is it possible to use a commercial CF card for the CPU module supporting CF card mounting?
Yes, it is possible. Use a card with the following memory capacities_ SPH300_ 2 GB or less SPH2000_ 32 GB or less (PIO mode supporting model) Note that so... Show Detail
- No：1593
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
Is the SX bus cable oil resistant?
The cable is not oil resistant so that you need to protect it by covering it with oil-resistant material. Show Detail
- No：1604
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
When the working CPU is running (in a normal or a nonfatal fault condition) and the standby CPU is standing by, the changed program is loaded into both CPUs... Show Detail
- No：1647
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Configure the communication settings acco... Show Detail
- No：1509
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:41
- Category： Support tool (D300win)
291-300 of Total 398