-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need to stop the CPU. Please consider the... Show Detail
- No：1661
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:05
- Category： Support tool (D300win)
-
What is the meaning of EN and ENO of functions in Expert (D300win)?
The EN and ENO terminals of functions mean the start operation terminal and the operation result terminal, respectively. ・When the variable connected to the... Show Detail
- No：1476
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:31
- Category： Support tool (D300win)
-
This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board. Show Detail
- No：1335
- Displayed Date：2023/04/25 19:00
- Category： Error
-
When you use preset operation in the linear operation mode, counting is sometimes discontinued due to preset overflow. Show Detail
- No：1675
- Displayed Date：2023/04/25 19:00
- Category： Function
-
There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosis' dialog, check the 'Resource inform... Show Detail
- No：1671
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
No, you cannot access the input (output) parameter (WV*, DV*) for which the data length is set in words/ double-words by using a bit address within the user ... Show Detail
- No：1677
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
You cannot upgrade 'MICREX-F PLC Programmer' free of change. 'MICREX-F PLC Programmer' that can be installed as NL4N-WNSB is currently included with the p... Show Detail
- No：1455
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 09:36
- Category： Support tool (Others)
-
In the system definition, group-type slave stations in any I/O configuration are registered as 'DeviceNet capsule.' In addition, the numbers of input and out... Show Detail
- No：1644
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Can I upload a definition file downloaded from a configurator to NP1L-PD1/PD2?
No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side. Show Detail
- No：1468
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
I bought a USB 3.0 cable (A-B type) to connect to FLT-ASFKA. However, I cannot connect them.
FLT-ASFKA is equipped with a USB2.0 (B type) connector. The connecter shape is different between USB 3.0 (B type) and a USB 2.0 (B type). Purchase a USB 2.0 ... Show Detail
- No：1457
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Others)
21-30 of Total 398