All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by d

R_STS = 1 means 'send buffer overflow' detected by the general-purpose communication module. Check the communication for

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the

The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Et

Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coa

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). T

The file transfer error occurs because the module driver is downloaded with the Ethernet module not recognized by the CP

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. Af

No, it cannot be used as it is. It requires resources to be added, the system configuration definitions to be changed,

Turn off the write-protect switch of the user ROM card, mount it on the CPU module and transfer a program to write it to

Search by category

Keyword Search

FAQ within [ PLC ]

281-290 of Total 398

≪ 29 / 40page ≫

How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
- Category： Function
When the MODBUS master standard expansion FB _C_modm operates, the receive status becomes R_STS = 1. This is not shown in the receive status list. ...

R_STS = 1 means 'send buffer overflow' detected by the general-purpose communication module. Check the communication format, communication interval and other... Show Detail
- No：1607
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
When I turned on the positioning control module (Type_ NP1F-MP2/MA2), the EMG/±OT LED lights up and positioning operation is disabled. What causes ...

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the wiring of the external equipment. (T... Show Detail
- No：1601
- Displayed Date：2023/04/25 19:00
- Category： Function
After I replaced an Ethernet module (Type_NP1L-ET1/ET2), it cannot communicate with the target device. What is a possible cause?

The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Ethernet module. After replacing an Eth... Show Detail
- No：1590
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?

Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
How long is the refresh cycle of the pulse count value data of the high-speed counter module (Type_ NP1F-HC2)?

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). The count data, however, will be refle... Show Detail
- No：1547
- Displayed Date：2023/04/25 19:00
- Category： Function
When I use an Ethernet module (Type_ NP1L-ET□) to download the system definitions and module driver, a file transfer error is generated. Why?

The file transfer error occurs because the module driver is downloaded with the Ethernet module not recognized by the CPU. For the CPU to recognize the Ethe... Show Detail
- No：1404
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Is it possible to read and write the IP address and port reference number of an Ethernet module (Type_ NP1L-ET1) by using a user application?

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. After writing, the power (or reset) o... Show Detail
- No：1370
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Communication (Ethernet)
With D300win, is it possible to use a project (user application) created for a CPU32K model as it is for another CPU (e.g., 74K model)?

No, it cannot be used as it is. It requires resources to be added, the system configuration definitions to be changed, I/O groups to be reset and other ta... Show Detail
- No：1369
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Support tool (D300win)
How can I write to the user ROM card of a standard CPU?

Turn off the write-protect switch of the user ROM card, mount it on the CPU module and transfer a program to write it to the user ROM card. Show Detail
- No：1344
- Displayed Date：2023/04/25 19:00
- Category： Main unit