-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
The battery supplied with a CPU module is used to back up the following memories in the CPU module when a PLC system is turned off. Basically, connect the ba... Show Detail
- No：1505
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:40
- Category： Main unit
-
Can I use both P-link and PE-link in one system?
No, you cannot. Show Detail
- No：1523
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The MICREX-SX does not include a communication module having interfaces with Mitsubishi's original networks, MELSEC-NET/B or NET/10 or CC-LINK. Alternativel... Show Detail
- No：1546
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The module counts feedback pulses even without Z-phase pulse signals. Note that when Z-phase pulse signals are not provided, origin return operation is dis... Show Detail
- No：1549
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Is it possible to use the M/L area in the user FB with the Standard Loader (Type_ NP4H-SWN)?
Yes_ however, it is not recommended in terms of program reuse. It is better to use internal memory such as M and L by connecting them to the I/O terminals ... Show Detail
- No：1565
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Does data monitoring of the I/O area require the module to be registered in the system definition?
Unless you register the module in the system definition and set the I/O group in the CPU parameters, data monitoring is disabled because no memory is reserve... Show Detail
- No：1581
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
You can access the memory from a PC by setting the general-purpose communication module (Type_ NP1L-RS2) to 'Loader' mode. Various loader commands have been... Show Detail
- No：1615
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
No, you can't. You can check the IP address by connecting the PC loader to the CPU module and monitoring the RAS information of the fault diagnosis function. Show Detail
- No：1616
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
The received data is cleared to 0. Therefore, be sure not to read (ignore) the data by application program. Reopening the FB (turning the 'OPEN' terminal fro... Show Detail
- No：1672
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
251-260 of Total 398