You cannot mount the following I/O modules_ (1) High-speed input module NP1X3206-A, (2) High-speed output module NP1Y32

You can refer to sample project Mptpf4.zwt stored in the ZIPPED folder in the D300win folder.

You should be careful because if the write protection is OFF, the ROM is rewritten simultaneously with the internal RAM

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated.

With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of

You cannot use D300win V2 for that. You can display them by using the grid-fixed type ladder editor of the D300win V3.

This problem is probably caused by the following reasons: [For SPH300/2000/3000 series] 1) The CPU mode selection switc

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without p

You can remove these warnings by deleting function blocks (FBs) that are not used in the program. Do either of the fol

Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

241-250 of Total 398

≪ 25 / 40page ≫

Are there any I/O modules that cannot be mounted on the T-link expansion base?

You cannot mount the following I/O modules_ 　(1) High-speed input module NP1X3206-A, (2) High-speed output module NP1Y32T09P1-A, (3) Analog input module NP... Show Detail
- No：1577
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
Do you have a connection example for the input variable of the compact positioning FB of the positioning FB package?

You can refer to sample project Mptpf4.zwt stored in the ZIPPED folder in the D300win folder. Show Detail
- No：1614
- Displayed Date：2023/04/25 19:00
- Category： Function
When I mount the user ROM card for the SPH200 (Type_ NP8PMF-16) without changing its write protection from OFF, is the content of the ROM protected?

You should be careful because if the write protection is OFF, the ROM is rewritten simultaneously with the internal RAM of the CPU during program download. Show Detail
- No：1617
- Displayed Date：2023/04/25 19:00
- Category： Main unit
With the high-speed output module (Type_ NP1Y32T09P1-A), the LED flashes but no pulse is output to the outside. What should I check?

The flashing of the LED of the high-speed output module (Type_ NP1Y32T09P1-A) indicates that pulse output is generated. If no pulse output is generated in t... Show Detail
- No：1291
- Displayed Date：2023/04/25 19:00
- Category： Function
What is the range of IP addresses that can be used for FL-net?

With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of *_ 1 to 254) Show Detail
- No：1301
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:19
- Category： Communication (Others)
Can I use the D300win V2 to display variable addresses and comments on the ladder screen or printout?

You cannot use D300win V2 for that. You can display them by using the grid-fixed type ladder editor of the D300win V3. Show Detail
- No：1440
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
I cannot download a project to the user ROM card inserted in the CPU. What is a possible cause?

This problem is probably caused by the following reasons: [For SPH300/2000/3000 series] 1) The CPU mode selection switch is not set at the 'UROM-TERM' pos... Show Detail
- No：1528
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:47
- Category： Support tool
What is the difference between the PID forward and backward operations when the PID FB package is used?

In the MV selection part in the PID FB, (1) the backward operation uses the internally calculated MV value (%) without processing it (as-is)_ and (2) the for... Show Detail
- No：1625
- Displayed Date：2023/04/25 19:00
- Category： Function
I have converted MICREX-F program to SX using StandardV3. After execute [Conversion All], many warning messages appear '*** (Function block (FB) na...

You can remove these warnings by deleting function blocks (FBs) that are not used in the program. Do either of the following methods: Method 1 1) After... Show Detail
- No：1655
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Which is the signal that indicates pulse output completion on the positioning control module (Type_ NP1F-MP2)?

Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of completion. When the number of pulses... Show Detail
- No：1548
- Displayed Date：2023/04/25 19:00
- Category： Function