-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
No, they do not have polarity because they use relay contacts. Show Detail
- No：1585
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
You can check it with the status indication LED on the front of the module. When a low battery voltage is detected, the CER LED on the front of the module ... Show Detail
- No：1620
- Displayed Date：2023/04/25 19:00
- Category： Function
-
To enable the 'output value reference input,' the output module must be actually mounted. If the output module is set as 'unimplemented' in the system config... Show Detail
- No：1637
- Displayed Date：2023/04/25 19:00
- Category： Application
-
No, you cannot use the I/O extension function in a multi-CPU configuration. Register a remote I/O master module in the normal mode or extension mode in a... Show Detail
- No：1651
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
Do addresses of T-link devices (slave stations) connected to T-link need to be consecutive?
No, they do not need to be consecutive. If there are a lot of unused addresses, it may be better to assign addresses at some intervals for the future expa... Show Detail
- No：1276
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:14
- Category： Communication (T-link)
-
A description in the brackets of an array must only include values or variable names. Writing an expression in brackets is not possible. Show Detail
- No：1307
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
The near zero signal/command pulse zero signal/positioning end signal/RDY signal of the status information signals are set to [1]. The interrupt input sig... Show Detail
- No：1318
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
-
Can the D300win cable (Type_ NP4H-CB2) be extended?
It can be extended by connecting a commercially-available LAN straight cable by using the connection kit. Extending the cable makes it more susceptible to t... Show Detail
- No：1386
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
Is it possible to indirectly specify the timer set value with the Standard Loader (Type_ NP4H-SWN)?
Yes, it is possible. Input a memory address (DLxx) instead of an immediate value as the operand of the timer instruction. Show Detail
- No：1407
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
Check the feedback pulse wiring (to make sure that a shielded twisted pair is used, wiring conditions are appropriate, etc.). One possible reason for the c... Show Detail
- No：1421
- Displayed Date：2023/04/25 19:00
- Category： Function
231-240 of Total 398