The execution order of the contacts and coils in a ladder circuit partly differs between MICREX-F and MICREX-SX. Theref

The Standard Loader (V2.0.3.0 or later) supports SC instruction of the same specification as that of the MICREX-F Series

This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board.

An order for one NP8B-BP means one plug will be delivered. If you need two plugs, order two pieces. The CPU module (Typ

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. Af

They cannot be monitored if the number of rows in the variable worksheet exceeds 2520. Divide the variable worksheet so

Select a T-link capsule and set the numbers of input/output words. By default, a POD requires one word for input and on

The communication specification of the remote master does not control remote devices by the station No. Therefore, you c

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the syste

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

Search by category

Keyword Search

FAQ within [ PLC ]

221-230 of Total 398

≪ 23 / 40page ≫

I converted a MICREX-F program to a MICREX-SX using StandardV3 loader. Contact and coil M8720 (TEMP0) which did not exist before conversion were cr...

The execution order of the contacts and coils in a ladder circuit partly differs between MICREX-F and MICREX-SX. Therefore, if a MICREX-F program is convert... Show Detail
- No：1657
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Does the SPH Series have SC instruction (step control instruction)?

The Standard Loader (V2.0.3.0 or later) supports SC instruction of the same specification as that of the MICREX-F Series. Show Detail
- No：1288
- Displayed Date：2023/04/25 19:00
- Category： Application
When I downloaded a program to the CPU module, a fatal fault occurred. I checked fault diagnosis and found both the CPU and I/O modules were indica...

This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board. Show Detail
- No：1335
- Displayed Date：2023/04/25 19:00
- Category： Error
If I order one SX bus loop-back plug (Type_ NP8B-BP), how many plugs will be delivered? Does it mean a set of two plugs?

An order for one NP8B-BP means one plug will be delivered. If you need two plugs, order two pieces. The CPU module (Type_ NP1P***) and integrated type int... Show Detail
- No：1338
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:34
- Category： Accessory
Is it possible to read and write the IP address and port reference number of an Ethernet module (Type_ NP1L-ET1) by using a user application?

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. After writing, the power (or reset) o... Show Detail
- No：1370
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Communication (Ethernet)
With D300win V2, I cannot monitor some of the variables in the global variable worksheet.

They cannot be monitored if the number of rows in the variable worksheet exceeds 2520. Divide the variable worksheet so that the number of rows is 2500 or... Show Detail
- No：1384
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 16:16
- Category： Support tool (D300win)
Please tell me how to register a T-link model of UG (or V Series) as a POD in the system definition.

Select a T-link capsule and set the numbers of input/output words. By default, a POD requires one word for input and one word for output. Show Detail
- No：1438
- Displayed Date：2023/04/25 19:00
- Category： Support tool
When a remote terminal master (NP1L-RM1) has been registered in 1-to-N or N-to-N mode in the system definition, can I register a remote device as '...

The communication specification of the remote master does not control remote devices by the station No. Therefore, you cannot register remote devices as 'No ... Show Detail
- No：1486
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Can I use a base board with station No. setup function (Type_ NP1B*-**S) as a standard base board (without 'S' at the end of type code)?

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the system definition of the loader designed f... Show Detail
- No：1531
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:50
- Category： Main unit
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function

221-230 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News