Calendar data conversion FB' is available as a program to extract the day of the week from the calendar data in the soft

You can check the address range of the CPU by using the loader or in the user's manual. In the Standard loader, after c

Check the following system memory. (1) Configuration information %MW10.52 to %MW10.67 (WSM52 to 67) (2) Configuratio

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redu

1) Double-click the 'Device' icon in the project view to open the device window. 2) Click the [Device Type] selection b

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have eith

This only stops the operating CPU and the operation is not switched to the standby CPU.

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input cu

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor.

Use the following communication cables from Furukawa Electric Co., Ltd. ・KPEV-SB 0.75mm2 x 1 pair (Max. length: 700m)

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

201-210 of Total 398

≪ 21 / 40page ≫

How can I know the day of the week on the calendar by using an application program?

Calendar data conversion FB' is available as a program to extract the day of the week from the calendar data in the software library of technical information... Show Detail
- No：1446
- Displayed Date：2023/04/25 19:00
- Category： Application
I am creating a program using SX-Programmer Standard. How can I check the address range of the memory devices that can be used in a program?

You can check the address range of the CPU by using the loader or in the user's manual. In the Standard loader, after creating a project, you can check the ... Show Detail
- No：1480
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
I use the hot plug base board with station No. setup function (Type_NP1BS-13D). When I remove a module, how can I identify the removed module in D3...

Check the following system memory. (1) Configuration information %MW10.52 to %MW10.67 (WSM52 to 67) (2) Configuration fault information %MW10.68 to %MW1... Show Detail
- No：1482
- Displayed Date：2023/04/25 19:00
- Category： Main unit
A CPU module has a rotary switch (0 to F) for setting the CPU No. on its front. What CPU No. should I set?

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redundant system which uses multiple CPU ... Show Detail
- No：1504
- Displayed Date：2023/04/25 19:00
- Category： Main unit
How can I display the list of device use status on Standard loaderV3

1) Double-click the 'Device' icon in the project view to open the device window. 2) Click the [Device Type] selection button (▼) and select a device the u... Show Detail
- No：1526
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:44
- Category： Support tool (Standard)
For 1-to-1 communication of Ethernet, can I establish communication only using a LAN cable (cross cable), without using a hub?

It depends on the specifications and combinations of Ethernet devices. Communication ports of Ethernet devices have either of the following specifications. ... Show Detail
- No：1582
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:55
- Category： Communication (Ethernet)
What happens when I set the key switch of the operating CPU to STOP while using the redundancy function of the SPH300? Is the operation switched t...

This only stops the operating CPU and the operation is not switched to the standby CPU. Show Detail
- No：1588
- Displayed Date：2023/04/25 19:00
- Category： Main unit
I will use the analog current input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input currents of the PLC, is expressed as i ... Show Detail
- No：1603
- Displayed Date：2023/04/25 19:00
- Category： I/O
I will use the analog voltage input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor. Show Detail
- No：1622
- Displayed Date：2023/04/25 19:00
- Category： I/O
What cable should I use for T-link?

Use the following communication cables from Furukawa Electric Co., Ltd. ・KPEV-SB 0.75mm2 x 1 pair (Max. length: 700m) ・T-KPEV-SB 1.25mm2 x 1 pair (Max. le... Show Detail
- No：1278
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)