We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of

The supported Windows OS depends on the loader version. Windows 7: V1.3.3.2 or later, Windows 8: V1.3.4.1 or late

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes p

Project printing is optimized printing. The column width of a print is fixed and cannot be adjusted.

There is a difference between 'Unpassive' and 'Fullpasisve' as follows. 1) Unpassive: Communicates with a device that h

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor.

The measurement accuracy does not include zero junction compensation accuracy. The zero junction compensation accuracy

Yes, it is possible. Use a card with the following memory capacities_ SPH300_ 2 GB or less SPH2000_ 32 GB or less (PI

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

191-200 of Total 398

≪ 20 / 40page ≫

Can I use a commercially available hub for FL-net modules?

We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of use for FL-net. * What is 'B.S'?... Show Detail
- No：1465
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:28
- Category： Communication (Others)
Which OS does MICREX-F PLC Programmer support?

The supported Windows OS depends on the loader version. Windows 7: V1.3.3.2 or later, Windows 8: V1.3.4.1 or later, Windows 8.1 and 10: V1.3.5.0 or... Show Detail
- No：1454
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Others)
With the DeviceNet master module (Type_ NP1L-DN1), how can I create a scan list and register it with the master module?

In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in the system configuration definitions... Show Detail
- No：1346
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:35
- Category： Communication (Others)
I use an Ethernet module (Type_ NP1L-ET1/ET2) to read/write data from/to a PC in the loader command communication mode. At what time are data read ...

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes place when a request is generated rega... Show Detail
- No：1300
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
With the LD/FBD editor of D300win V3, I printed a project and the column width was very narrow. Is there any way to adjust the column width?

Project printing is optimized printing. The column width of a print is fixed and cannot be adjusted. Show Detail
- No：1284
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
In the Ethernet module communication setting, when I select 'Unpassive' communication port opens. However, if 'Fullpassive,' unable to open communi...

There is a difference between 'Unpassive' and 'Fullpasisve' as follows. 1) Unpassive: Communicates with a device that has any IP or port No. 2) Fullpassi... Show Detail
- No：1630
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:01
- Category： Communication (Ethernet)
I will use the analog voltage input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor. Show Detail
- No：1622
- Displayed Date：2023/04/25 19:00
- Category： I/O
Does the accuracy specification of the thermocouple input module (Type_ NP1AXH4-TC) include zero junction compensation accuracy?

The measurement accuracy does not include zero junction compensation accuracy. The zero junction compensation accuracy is ±1°C (at ambient temperature 0°C ... Show Detail
- No：1597
- Displayed Date：2023/04/25 19:00
- Category： I/O
Is it possible to use a commercial CF card for the CPU module supporting CF card mounting?

Yes, it is possible. Use a card with the following memory capacities_ 　SPH300_ 2 GB or less SPH2000_ 32 GB or less (PIO mode supporting model) Note that so... Show Detail
- No：1593
- Displayed Date：2023/04/25 19:00
- Category： Accessory
How can I provide Z-phase pulses when the equipment connected with the positioning control module (Type_ NP1F-MP2/MA2) uses a stepping motor?

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
- Category： Function