No, you cannot. Use NW0H-CNV (RS-232C/RS-422 converter) or NP4H-CVU (USB/RS-422 converter) in combination with NW0H-CA3

There is a difference between 'Unpassive' and 'Fullpasisve' as follows. 1) Unpassive: Communicates with a device that ha

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need

Both Standard and Expert (D300win) are program loader software for the SX series. However, there is no compatibility be

Since the primary battery built in the SPF main unit cannot be replaced, the battery connection switch is set to off at

Yes, you can connect MICREX-F series and SX series P-link modules, and communicate between them. * For the connection a

Check that the terminating plug is attached. Check also that the SX bus expansion cable is not broken. You need to att

This error occurs if data is received and the receive buffer is attempted to be overwritten while data in the receive b

The following devices are necessary to connect a personal computer loader and a MICREX-F series PLC: a loader adapter FL

Possible causes are as follows: 1) The baud rate differs between the PLC and the target device. 2) The stop bit differ

Search by category

Keyword Search

FAQ within [ PLC ]

11-20 of Total 398

≪ 2 / 40page ≫

Can I use a converter manufactured by Black Box in combination with the loader cable (Type_NW0H-CA3)?

No, you cannot. Use NW0H-CNV (RS-232C/RS-422 converter) or NP4H-CVU (USB/RS-422 converter) in combination with NW0H-CA3 Show Detail
- No：1303
- Displayed Date：2023/04/25 19:00
- Category： Accessory
In the Ethernet module communication setting, when I select 'Unpassive' communication port opens. However, if 'Fullpassive,' unable to open communi...

There is a difference between 'Unpassive' and 'Fullpasisve' as follows. 1) Unpassive: Communicates with a device that has any IP or port No. 2) Fullpassi... Show Detail
- No：1630
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:01
- Category： Communication (Ethernet)
When I change a program online (patch POU), error message shown 'The resevation area of the non-retain memory of POU xxx is short (2 word).' Why?

Once a compilation error occurs during patch POU, the project must be compiled and downloaded again. Therefore, you need to stop the CPU. Please consider the... Show Detail
- No：1661
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:05
- Category： Support tool (D300win)
I want to edit the program of the PLC (SX series). In the catalogue and website, I found that two types of program loaders, Standard and Expert (D3...

Both Standard and Expert (D300win) are program loader software for the SX series. However, there is no compatibility between program data (called 'project')... Show Detail
- No：1646
- Displayed Date：2023/04/25 19:00
- Category： Support tool
Newly purchased SPF shows Battery error. How can I solve it ?

Since the primary battery built in the SPF main unit cannot be replaced, the battery connection switch is set to off at the factory shipment. By turning on t... Show Detail
- No：1525
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Can I connect MICREX-F series and SX series P-link modules via P-link?

Yes, you can connect MICREX-F series and SX series P-link modules, and communicate between them. * For the connection and communication methods, see 'Sectio... Show Detail
- No：1460
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
In the diagnostic screen, error message 'Fatal failure SX bus error Time up error of deciding SBM use mode' appeared. What are the possible cause...

Check that the terminating plug is attached. Check also that the SX bus expansion cable is not broken. You need to attach an SX bus terminating plug at bot... Show Detail
- No：1648
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
A communication error (overrun error or receive buffer overflow) occurred on communication module (NP1L-RS1/RS2/RS3/RS4/RS5). What are the possible...

This error occurs if data is received and the receive buffer is attempted to be overwritten while data in the receive buffer is being read to the memory in ... Show Detail
- No：1629
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I want to use a personal computer loader with a MICREX-F series PLC.

The following devices are necessary to connect a personal computer loader and a MICREX-F series PLC: a loader adapter FLT-ASFKA (or FLT-ASFK), and a USB cab... Show Detail
- No：1459
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 09:37
- Category： Support tool (Others)
A communication error occurred, saying it was caused by a framing error. What causes a framing error?

Possible causes are as follows: 1) The baud rate differs between the PLC and the target device. 2) The stop bit differs between the PLC and the target devi... Show Detail
- No：1275
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:13
- Category： Communication (Others)