-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
Does an RS-485 communication module (Type_ NP1L-RS1/RS4/RS5, etc.) support the MODBUS procedure?
The SX-Programmer Expert supports MODBUS communication (master function) using an FB. Communication with a MODBUS slave device is possible by using SPH_CP... Show Detail
- No：1380
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
- Category： Communication (Others)
-
Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
- Category： Communication (Others)
-
It enables reception only when CD (Carrier Detection) is ON. (Other operations are the same as those in the DTE mode.) Show Detail
- No：1598
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
Does the general-purpose communication module support the BSC procedure?
No, it doesn't. Show Detail
- No：1293
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
What is the range of IP addresses that can be used for FL-net?
With FL-net, Class C IP addresses are used. The range of Class C IP addresses is 192.0.0.* to 233.255.255.*. (Range of *_ 1 to 254) Show Detail
- No：1301
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:19
- Category： Communication (Others)
-
The number of M_OPEN FBs that can be opened simultaneously is limited to 56. The number of FBs that can be simultaneously opened for each module depends on t... Show Detail
- No：1435
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
While NP1F-HC2 requires an external power supply of 5 V DC, NP1F-HC8 produces 5 V DC within the module from an external 24 V DC power supply and does not req... Show Detail
- No：1341
- Displayed Date：2023/04/25 19:00
- Category： Function
-
In MICREX-SX, a scan list is automatically created by registering the remote I/O to be connected to the master module in the system configuration definitions... Show Detail
- No：1346
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:35
- Category： Communication (Others)
-
Clock adjustment is initiated from CPU0 (operating) to other CPUs (standby). It takes place on a constant (1-minute) cycle at the time of and after system st... Show Detail
- No：1401
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
For what application is the base board with station number setting switch used?
It is used as a base specified for 'system fail-soft start-up' operation, which is set when there is any base with some modules on which power is not turned ... Show Detail
- No：1411
- Displayed Date：2023/04/25 19:00
- Category： Main unit
11-20 of Total 398