-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
What standards does the MICREX-SX series comply with?
Fuji Electric website provides information on the standards that the MICREX-SX series complies with. Visit the following URL. Show Detail
- No：1358
- Displayed Date：2023/04/25 19:00
- Category： Others
-
Up to 127 levels of nesting is possible. Show Detail
- No：1431
- Displayed Date：2023/04/25 19:00
- Category： Application
-
The error occurs because the address display mode is set to 'FLEX-PC,' but the address representation of the word device is not hexadecimal. For the addres... Show Detail
- No：1496
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
In the standard expansion counter FB _MHCNTH, CH0 operates but CH1 does not.
It seems that this problem was caused by an improper address setting for INDAT/OUTDAT assigned to the counter FB terminal. On a single module, assign the sa... Show Detail
- No：1539
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The module counts feedback pulses even without Z-phase pulse signals. Note that when Z-phase pulse signals are not provided, origin return operation is dis... Show Detail
- No：1549
- Displayed Date：2023/04/25 19:00
- Category： Function
-
Yes, you can. On the 'Load from PLC' dialog, check 'Reflect Real Structure,' and then connect the PLC online. If this option is checked, the loader internall... Show Detail
- No：1610
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
You should be careful because if the write protection is OFF, the ROM is rewritten simultaneously with the internal RAM of the CPU during program download. Show Detail
- No：1617
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
Yes, you can. Note, however, that the input impedance reduces to half. Pay attention to the drive ability of the sensor. Show Detail
- No：1622
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software offset setting will be disabled. Show Detail
- No：1667
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosis' dialog, check the 'Resource inform... Show Detail
- No：1671
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
181-190 of Total 398