While NP1F-HC2 requires an external power supply of 5 V DC, NP1F-HC8 produces 5 V DC within the module from an external

No, it is not possible. Use an encoder of the line-driver or open-collector output type. When using a line-driver type,

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare v

To make the 'Use USB port' check box selectable, the USB driver for MICREX-SX must be installed on the PC in use. Insta

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes p

Use the 'SX control utility' software. This software is included in both D300win and Standard software. The utility in

Project printing is optimized printing. The column width of a print is fixed and cannot be adjusted.

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'n

Timers (or other FBs such as counters) each have an internal memory that is called an instance. Therefore, after copyi

Yes, it is. The bit arrangement (weighting) is opposite between the SX Series and F Series. - SX Series_ LSB_ Bit 0

Search by category

Keyword Search

FAQ within [ PLC ]

161-170 of Total 398

≪ 17 / 40page ≫

What is the difference in the open-collector pulse input between the high-speed counter (Type_ NP1F-HC2) and the multi-channel counter (Type_ NP1F-...

While NP1F-HC2 requires an external power supply of 5 V DC, NP1F-HC8 produces 5 V DC within the module from an external 24 V DC power supply and does not req... Show Detail
- No：1341
- Displayed Date：2023/04/25 19:00
- Category： Function
Is it possible to use an encoder of the complementary output type for the high-speed counter module (Type_ NP1F-HC2)?

No, it is not possible. Use an encoder of the line-driver or open-collector output type. When using a line-driver type, pay attention to the output capacity ... Show Detail
- No：1320
- Displayed Date：2023/04/25 19:00
- Category： Function
I use the high-speed counter module (Type_ NP1F-HC2) FB. The compare value is larger than the present counter value but the compare output becomes ...

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare value is written by turning the data w... Show Detail
- No：1309
- Displayed Date：2023/04/25 19:00
- Category： Function
Of the communication port settings (MICREX-SX) of the Standard Loader (Type_ NP4H-SWN), the 'Use USB port' check box cannot be selected.

To make the 'Use USB port' check box selectable, the USB driver for MICREX-SX must be installed on the PC in use. Install the USB driver (dedicated) conta... Show Detail
- No：1306
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:31
- Category： Support tool (Standard)
I use an Ethernet module (Type_ NP1L-ET1/ET2) to read/write data from/to a PC in the loader command communication mode. At what time are data read ...

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes place when a request is generated rega... Show Detail
- No：1300
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
Is there any way to back up the internal data of the CPU by using the loader?

Use the 'SX control utility' software. This software is included in both D300win and Standard software. The utility included in either of them has the ... Show Detail
- No：1294
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:18
- Category： Support tool
With the LD/FBD editor of D300win V3, I printed a project and the column width was very narrow. Is there any way to adjust the column width?

Project printing is optimized printing. The column width of a print is fixed and cannot be adjusted. Show Detail
- No：1284
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
To debug a PLC program without I/O module, I set I/Os as 'no equipment'. Then, I tried to set input contact (X) using switch of MONITOUCH. However,...

In Standard loader, to access the input memory from MONITOUCH, cancel the I/O group setting of the input specified as 'no equipment.' If the input specified... Show Detail
- No：1658
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 14:04
- Category： Support tool (Standard)
In Expert (D300win), I copied and pasted an existing timer (or counter) to add timer. However, a compilation error (Function block or structure cor...

Timers (or other FBs such as counters) each have an internal memory that is called an instance. Therefore, after copying a timer, you need to define a vari... Show Detail
- No：1656
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
I heard that the bit arrangement is opposite between the MICREX-SX Series and MICREX-F Series. Is this true?

Yes, it is. The bit arrangement (weighting) is opposite between the SX Series and F Series. - SX Series_ LSB_ Bit 0 MSB_ Bit 15 (D300win) Bi... Show Detail
- No：1618
- Displayed Date：2023/04/25 19:00
- Category： Application

161-170 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News