Yes, it is possible. Input a memory address (DLxx) instead of an immediate value as the operand of the timer instruction

By changing the zoom rate of the main screen displaying a program or data monitoring, the on-screen font size is also i

When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, s

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the syste

The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment,

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to

Index modification is not available with D300win. This is because D300win is dedicated to programmable controllers (PLC

The '.BSM' file is intended for manufacturers' maintenance purposes. You can check fault information by opening the '.R

Search by category

Keyword Search

FAQ within [ PLC ]

151-160 of Total 398

≪ 16 / 40page ≫

Is it possible to indirectly specify the timer set value with the Standard Loader (Type_ NP4H-SWN)?

Yes, it is possible. Input a memory address (DLxx) instead of an immediate value as the operand of the timer instruction. Show Detail
- No：1407
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Can I increase the font size displayed on the Standard loader screen?

By changing the zoom rate of the main screen displaying a program or data monitoring, the on-screen font size is also increased or decreased. However, the S... Show Detail
- No：1501
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Can I replace NP1L-FL2 with NP1L-FL3 for FL-net communication?

When connected via 10BASE-T, you can replace it. There is no need to change the system definition. Before replacement, set the switches on the front of the N... Show Detail
- No：1524
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
Can I use a base board with station No. setup function (Type_ NP1B*-**S) as a standard base board (without 'S' at the end of type code)?

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the system definition of the loader designed f... Show Detail
- No：1531
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:50
- Category： Main unit
The SPH300EX (Type_ NP1PS-74D) has an SX bus connector. Which ports should I use when connecting the SX bus cable to the SX bus expansion base, 'IN...

The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment, connect the cable to the IN (input)... Show Detail
- No：1535
- Displayed Date：2023/04/25 19:00
- Category： Main unit
I don't have the SX bus loop-back plug (Type_ NP8B-BP). Can I use the SX bus cable instead?

You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors at both ends of the cable to IN and ... Show Detail
- No：1543
- Displayed Date：2023/04/25 19:00
- Category： Accessory
I use the high-speed counter module (Type_ NP1F-HC□). The user's manual (FEH210) shows 'Multiplication function_ x1, x4.' How can I switch between ...

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_ ･ Forward pulse + Reverse pulse_ x1 ... Show Detail
- No：1564
- Displayed Date：2023/04/25 19:00
- Category： Function
Pulse counting is disabled on the high-speed input module (Type_ NP1X3206-A). What should I check?

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to '1.' If the pulse count data regist... Show Detail
- No：1570
- Displayed Date：2023/04/25 19:00
- Category： Function
Does the D300win offer any method to specify variable names (or direct addresses) indirectly on a program (like a specification method generally ca...

Index modification is not available with D300win. This is because D300win is dedicated to programmable controllers (PLCs) conforming to the internal standar... Show Detail
- No：1591
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
When I saved RAS information in a file during the fault diagnosis of the SX, files with '.RAS' and '.BSM' extensions were created and I don't know ...

The '.BSM' file is intended for manufacturers' maintenance purposes. You can check fault information by opening the '.RAS' file with Notepad or another tex... Show Detail
- No：1608
- Displayed Date：2023/04/25 19:00
- Category： Support tool