-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
When the site environment is unfavorable, you are recommended to use the dedicated loader cable. Version V3.2.0.0 or later or V2.2.6.0 or later of D300win ... Show Detail
- No：1423
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
You can check the address range of the CPU by using the loader or in the user's manual. In the Standard loader, after creating a project, you can check the ... Show Detail
- No：1480
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
The following CPU modules and versions support the above. ・ NP1PH-08/16: V22 or later ・ NP1PS-32:V26 or later ・ NP1PS-32R/74R/117R:V29 or later ・ NP1PS-2... Show Detail
- No：1481
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
How much space is necessary between the SPF series main unit and each expansion unit?
You can install the SPF series main unit and each expansion unit without space between them. Show Detail
- No：1517
- Displayed Date：2023/04/25 19:00
- Category： Main unit
-
The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). The count data, however, will be refle... Show Detail
- No：1547
- Displayed Date：2023/04/25 19:00
- Category： Function
-
A nonfatal fault of the takt cycle monitoring error has occurred. What is a possible cause?
The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the system definition is shorter than the ac... Show Detail
- No：1576
- Displayed Date：2023/04/25 19:00
- Category： Error
-
Possible causes are as follows: 1) The baud rate differs between the PLC and the target device. 2) The stop bit differs between the PLC and the target devi... Show Detail
- No：1275
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:13
- Category： Communication (Others)
-
Of the array element Nos., [0] is assigned to the 0th bit and [31] to the 31st bit. Show Detail
- No：1345
- Displayed Date：2023/04/25 19:00
- Category： Application
-
They are assigned from words with the lowest numbers in a left-justified manner. Show Detail
- No：1385
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
The redundant function of the SPH Series provides redundancy only for the CPU and it cannot make the Ethernet redundant. Show Detail
- No：1392
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
141-150 of Total 398