Set the number of timers according to the number actually used. By simply specifying 8192 or a larger value as the time

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of

The MICREX-SX is assumed to be installed inside a dustproof type switchboard in a general factory. There is a wide vari

This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed c

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redu

Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a co

You can use the following program as an alternative. When you turn on the differential command 'M0,' the differential

This was probably caused by the following factors (1) The PC was not restarted after the D300win was installed. (2) A

The SPH Series does not include an I/O connector. A soldering type connector is available as an option sold separately (

Unfortunately, information in a device connected to the master module cannot be read even by building a user application

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

131-140 of Total 398

≪ 14 / 40page ≫

A global timer with the Standard Loader, T8192 or a larger value must be specified as the timer address. Do I need to set the number of timers as 8...

Set the number of timers according to the number actually used. By simply specifying 8192 or a larger value as the timer number, a global timer can be used. Show Detail
- No：1635
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Although the LED for ±OT lights up on the positioning control module (Type_ NP1F-MP2/MA2), the positioning operation finishes. What is the causal f...

This was probably caused by one of the following two factors_ (1) ±OT is set to 'Disabled' in the parameter setting of the positioning control module (Type_... Show Detail
- No：1575
- Displayed Date：2023/04/25 19:00
- Category： Function
The physical environmental conditions of the MICREX-SX specify 'Free from corrosive gases.' Please specifically explain this environment.

The MICREX-SX is assumed to be installed inside a dustproof type switchboard in a general factory. There is a wide variety of corrosive gas environments dep... Show Detail
- No：1566
- Displayed Date：2023/04/25 19:00
- Category： Others
I have connected the SPH Series with the POD (UG Series) via the T-link. A code F8 is displayed on the screen of the POD. What is a possible cause?

This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed contact on the POD (UG), (3) Improp... Show Detail
- No：1559
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
A CPU module has a rotary switch (0 to F) for setting the CPU No. on its front. What CPU No. should I set?

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redundant system which uses multiple CPU ... Show Detail
- No：1504
- Displayed Date：2023/04/25 19:00
- Category： Main unit
What is the type of the configurator that is used with NP1L-PD1/PD2?

Use the following types of configurators: 'CONF-PDP' for NP1L-PD1 and 'NetTool for Profibus' for NP1L-PD2. Purchase a configurator from HMS Industrial Networ... Show Detail
- No：1494
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I used up differential relay memory. Can I create differential instructions by an application program?

You can use the following program as an alternative. When you turn on the differential command 'M0,' the differential output 'M2' turns ON for one scan. ... Show Detail
- No：1458
- Displayed Date：2023/04/25 19:00
- Category： Application
The version of the D300win is displayed as Version 4.0. Why?

This was probably caused by the following factors (1) The PC was not restarted after the D300win was installed. (2) A space is included in the name of the... Show Detail
- No：1441
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
Doesn't the connector type I/O module of the SPH Series include a connector as an accessory?

The SPH Series does not include an I/O connector. A soldering type connector is available as an option sold separately (NP8V-CN). Show Detail
- No：1426
- Displayed Date：2023/04/25 19:00
- Category： I/O
Is there any way to check the vendor ID, product code, product revision, serial No., etc. of the slave from the DeviceNet master module (Type_ NP1L...

Unfortunately, information in a device connected to the master module cannot be read even by building a user application. Please use the dedicated configura... Show Detail
- No：1387
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)