This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed c

You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Confi

You can check the address range of the CPU by using the loader or in the user's manual. In the Standard loader, after c

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side.

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected.

Fuji Electric website provides information on the standards that the MICREX-SX series complies with. Visit the following

For an alarm contact output of an error of the PLC system, select an arbitrary output module in the system definitions a

This is because when a compilation process is carried out, automatically assigned variables (variables for which AT spec

Yes, it is possible. Use a card with the following memory capacities_ SPH300_ 2 GB or less SPH2000_ 32 GB or less (PI

Unless you register the module in the system definition and set the I/O group in the CPU parameters, data monitoring is

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

121-130 of Total 398

≪ 13 / 40page ≫

I have connected the SPH Series with the POD (UG Series) via the T-link. A code F8 is displayed on the screen of the POD. What is a possible cause?

This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed contact on the POD (UG), (3) Improp... Show Detail
- No：1559
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
I would like to read and write data by the SX-Programmer Expert (D300win). How do I configure the communication settings for SPH series CPUs?

You can connect an SX series CPU to D300win via USB, Ethernet or a dedicated loader cable, depending on the model. Configure the communication settings acco... Show Detail
- No：1509
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:41
- Category： Support tool (D300win)
I am creating a program using SX-Programmer Standard. How can I check the address range of the memory devices that can be used in a program?

You can check the address range of the CPU by using the loader or in the user's manual. In the Standard loader, after creating a project, you can check the ... Show Detail
- No：1480
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Can I upload a definition file downloaded from a configurator to NP1L-PD1/PD2?

No, you cannot upload a definition file. So, it is very important to keep backup of Definition file on PC side. Show Detail
- No：1468
- Displayed Date：2023/04/25 19:00
- Category： Support tool
I want to run an external device by pulse output with the high-speed output module (Type_ NP1Y32T09P1-A). What are the points to note regarding the...

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected. (2) The Z-phase/timing input signal f... Show Detail
- No：1399
- Displayed Date：2023/04/25 19:00
- Category： Function
What standards does the MICREX-SX series comply with?

Fuji Electric website provides information on the standards that the MICREX-SX series complies with. Visit the following URL. Show Detail
- No：1358
- Displayed Date：2023/04/25 19:00
- Category： Others
Is there an alarm output contact to use when an error occurs in the PLC system?

For an alarm contact output of an error of the PLC system, select an arbitrary output module in the system definitions and define its 0th bit as a 'system DO... Show Detail
- No：1347
- Displayed Date：2023/04/25 19:00
- Category： Main unit
When I use D300win to add variables to a certain POU and compile it for comparison, a 'comparison error' occurs even in a POU irrelevant to the cha...

This is because when a compilation process is carried out, automatically assigned variables (variables for which AT specification is not used) and FB instanc... Show Detail
- No：1336
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
Is it possible to use a commercial CF card for the CPU module supporting CF card mounting?

Yes, it is possible. Use a card with the following memory capacities_ 　SPH300_ 2 GB or less SPH2000_ 32 GB or less (PIO mode supporting model) Note that so... Show Detail
- No：1593
- Displayed Date：2023/04/25 19:00
- Category： Accessory
Does data monitoring of the I/O area require the module to be registered in the system definition?

Unless you register the module in the system definition and set the I/O group in the CPU parameters, data monitoring is disabled because no memory is reserve... Show Detail
- No：1581
- Displayed Date：2023/04/25 19:00
- Category： Support tool