It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. Af

The file transfer error occurs because the module driver is downloaded with the Ethernet module not recognized by the CP

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). T

Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coa

The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Et

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the

R_STS = 1 means 'send buffer overflow' detected by the general-purpose communication module. Check the communication for

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by d

To enable the 'output value reference input,' the output module must be actually mounted. If the output module is set as

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of

Search by category

Keyword Search

FAQ within [ PLC ]

111-120 of Total 398

≪ 12 / 40page ≫

Is it possible to read and write the IP address and port reference number of an Ethernet module (Type_ NP1L-ET1) by using a user application?

It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. After writing, the power (or reset) o... Show Detail
- No：1370
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Communication (Ethernet)
When I use an Ethernet module (Type_ NP1L-ET□) to download the system definitions and module driver, a file transfer error is generated. Why?

The file transfer error occurs because the module driver is downloaded with the Ethernet module not recognized by the CPU. For the CPU to recognize the Ethe... Show Detail
- No：1404
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
How long is the refresh cycle of the pulse count value data of the high-speed counter module (Type_ NP1F-HC2)?

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). The count data, however, will be refle... Show Detail
- No：1547
- Displayed Date：2023/04/25 19:00
- Category： Function
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?

Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
After I replaced an Ethernet module (Type_NP1L-ET1/ET2), it cannot communicate with the target device. What is a possible cause?

The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Ethernet module. After replacing an Eth... Show Detail
- No：1590
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
When I turned on the positioning control module (Type_ NP1F-MP2/MA2), the EMG/±OT LED lights up and positioning operation is disabled. What causes ...

Check the following two points (1) To use the EMG/±OT signal, input the 'External power supply 24 V DC.' (2) Check the wiring of the external equipment. (T... Show Detail
- No：1601
- Displayed Date：2023/04/25 19:00
- Category： Function
When the MODBUS master standard expansion FB _C_modm operates, the receive status becomes R_STS = 1. This is not shown in the receive status list. ...

R_STS = 1 means 'send buffer overflow' detected by the general-purpose communication module. Check the communication format, communication interval and other... Show Detail
- No：1607
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
How do I perform pulse output with the high-speed output module (Type_NP1Y32T09P1-A)?

All the channels in the high-speed output module are set to the general purpose output mode (normal digital output) by default. To use the module in the pul... Show Detail
- No：1613
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
- Category： Function
In a multi-CPU system, I set the 'Output reference input' of the I/O group registration but the variable (contact) specified for the output referen...

To enable the 'output value reference input,' the output module must be actually mounted. If the output module is set as 'unimplemented' in the system config... Show Detail
- No：1637
- Displayed Date：2023/04/25 19:00
- Category： Application
I understand that an analog input module (Type_ NP1AXH4-MR, etc.) has a signal line breakage detection function. How does it work?

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of 0.92 V or lower for the 1 to 5 V ran... Show Detail
- No：1316
- Displayed Date：2023/04/25 19:00
- Category： I/O

111-120 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News