No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input cu

_F_WRITE_CSV_DINT' may be influenced by the file search time depending on the number of files in the CF. The time it ta

After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software off

When the CPU module is stopped, the positioning operation stops.

You can install a T-link master (processor part in the case of MICREX-F series) at any position on the T-link transmissi

To input the initial value, input '[value, value, ..., value].' In brackets, input values and use commas to separate va

Data with an address with the smaller number is arranged on the lower-order side. For example, DM0 consists of two word

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with po

A compilation error occurs if the properties of the POU do not match. Specify the CPU type as 'Common.'

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a lin

Search by category

Keyword Search

FAQ within [ PLC ]

101-110 of Total 398

≪ 11 / 40page ≫

I will use the analog current input module. Can I input a single input signal to two CHs of the module simultaneously (in parallel) to use them?

No, you can't. The relationship between i, which is the sensor output current, and i1 and i2, which are the CH input currents of the PLC, is expressed as i ... Show Detail
- No：1603
- Displayed Date：2023/04/25 19:00
- Category： I/O
The '_F_WRITE_CSV_DINT' FB allows a CSV file to be output to the memory card. How frequently can data be written? Is there any specific data of the...

_F_WRITE_CSV_DINT' may be influenced by the file search time depending on the number of files in the CF. The time it takes for 100 (200-word) DINT data to b... Show Detail
- No：1634
- Displayed Date：2023/04/25 19:00
- Category： Application
When I set offset on the analog module (NP1AXH8I-MR) by using software (parameters) and disable the software offset setting by operating hardware (...

After changing the range with the rotary switch, turn off the power once and then turn it on again, and the software offset setting will be disabled. Show Detail
- No：1667
- Displayed Date：2023/04/25 19:00
- Category： I/O
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...

When the CPU module is stopped, the positioning operation stops. Show Detail
- No：1669
- Displayed Date：2023/04/25 19:00
- Category： Function
When connecting devices on T-link, do I have to install a T-link master at the starting point (either end) of the connection configuration?

You can install a T-link master (processor part in the case of MICREX-F series) at any position on the T-link transmission line. Show Detail
- No：1280
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
In a variable worksheet of D300win V3, how can I input the 'initial value' when a variable in a one-dimensional array is used?

To input the initial value, input '[value, value, ..., value].' In brackets, input values and use commas to separate values. Show Detail
- No：1299
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:19
- Category： Support tool (D300win)
When a double-word address is used with the Standard Loader (Type_ NP4H-SWN), how are words arranged in terms of the higher and lower order?

Data with an address with the smaller number is arranged on the lower-order side. For example, DM0 consists of two words_ WM0 and WM1. WM0 is arranged on th... Show Detail
- No：1305
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
When the pulse catch function of the high-speed input module (Type_ NP1X3206-A) is used, can all points be used? Is any difference made to the puls...

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with ports 1 to 8. With ports 9 to 32, pu... Show Detail
- No：1321
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
- Category： Function
With D300win, when I paste user FBs together with the POU from another project, a compilation error occurs. Why?

A compilation error occurs if the properties of the POU do not match. Specify the CPU type as 'Common.' Show Detail
- No：1326
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
- Category： Support tool (D300win)
Is it possible to use the optical converter NP1L-OL1 between processors as with the P-link?

The optical converter NP1L-OL1 is an optical converter of the SX bus. It cannot be used because the SX bus is not a link between processors. Show Detail
- No：1327
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:31
- Category： Communication (Others)

101-110 of Total 398

PLC

Common to N
- Support tool (Others)
Common to SX
- Support tool (D300win)
- |Application
- |Support tool
- |Support tool (Standard)
- |Others
- |Accessory
- |Error
- |Communication (T-link)
- |Function
- |Communication (Others)
- |Main unit
- |Communication (Ethernet)

SPB
SPF
- Others
- |Support tool
- |Communication (Ethernet)
- |Communication (Others)
- |Main unit
- |Application

SPH
- Communication (T-link)
- |Support tool (D300win)
- |Others
- |Communication (Others)
- |Main unit
- |Function
- |Communication (Ethernet)
- |Application
- |Accessory
- |Support tool (Standard)
- |I/O
- |Error
- |Support tool

Info & News

To Top of Page

PLC

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability

Latest FAQ

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

PLC

Info & News