You can display the mismatch circuit in the program and differences using the 'Verify' command of the Standard loader.

The IP address is not assigned automatically. (DHCP function is not supported.) The default IP address is '192.168.0

No, you can't. The MICREX-SX shows an EC directive conformity declaration (self-declaration) as a single PLC unit. For

You can order sulfurized gas-resistant models by adding /Z4 at the end of product type code of the MICREX-SX SPH. Or, co

It can be extended by connecting a commercially-available LAN straight cable by using the connection kit. Extending the

This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board.

Yes, it is possible. Use a card with the following memory capacities_ SPH300_ 2 GB or less SPH2000_ 32 GB or less (PI

To use a CF card as user ROM of the SPH Series, you need to format the CF card and initialize it (generate folders and f

The MICREX-SX is assumed to be installed inside a dustproof type switchboard in a general factory. The amount of dust m

The '.BSM' file is intended for manufacturers' maintenance purposes. You can check fault information by opening the '.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC

Latest FAQ

I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...

GLOBAL

Search by category

Keyword Search

FAQ within [ PLC ]

91-100 of Total 398

≪ 10 / 40page ≫

When comparing the project in CPU with that in the personal computer by Standard loader, a mismatch between the programs was detected. How can I fi...

You can display the mismatch circuit in the program and differences using the 'Verify' command of the Standard loader. After uploading the project from the... Show Detail
- No：1664
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
I use the Ethernet module (Type_NP1L-ET1). Is the IP address assigned automatically?

The IP address is not assigned automatically. (DHCP function is not supported.) The default IP address is '192.168.0.1'. You can check the IP address b... Show Detail
- No：1595
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
I used only the MICREX-SX and electrical devices with CE Marking in a control panel. Can I show CE Marking on this control panel?

No, you can't. The MICREX-SX shows an EC directive conformity declaration (self-declaration) as a single PLC unit. For the conformity declaration as contro... Show Detail
- No：1540
- Displayed Date：2023/04/25 19:00
- Category： Others
I want MICREX-SX SPH models designed to resist sulfurized gas.

You can order sulfurized gas-resistant models by adding /Z4 at the end of product type code of the MICREX-SX SPH. Or, contact your Fuji Electric sales repres... Show Detail
- No：1425
- Displayed Date：2023/04/25 19:00
- Category： Others
Can the D300win cable (Type_ NP4H-CB2) be extended?

It can be extended by connecting a commercially-available LAN straight cable by using the connection kit. Extending the cable makes it more susceptible to t... Show Detail
- No：1386
- Displayed Date：2023/04/25 19:00
- Category： Accessory
When I downloaded a program to the CPU module, a fatal fault occurred. I checked fault diagnosis and found both the CPU and I/O modules were indica...

This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board. Show Detail
- No：1335
- Displayed Date：2023/04/25 19:00
- Category： Error
Is it possible to use a commercial CF card for the CPU module supporting CF card mounting?

Yes, it is possible. Use a card with the following memory capacities_ 　SPH300_ 2 GB or less SPH2000_ 32 GB or less (PIO mode supporting model) Note that so... Show Detail
- No：1593
- Displayed Date：2023/04/25 19:00
- Category： Accessory
What operation do I need to use a CF card as a user ROM card used for the CPU module of the SPH Series (SPH300 or SPH2000)?

To use a CF card as user ROM of the SPH Series, you need to format the CF card and initialize it (generate folders and files in the user ROM). The format sh... Show Detail
- No：1439
- Displayed Date：2023/04/25 19:00
- Category： Accessory
The physical environmental conditions of the MICREX-SX specify 'Pollution degree 2.' Please specifically explain this environment.

The MICREX-SX is assumed to be installed inside a dustproof type switchboard in a general factory. The amount of dust mentioned above is assumed to cause no... Show Detail
- No：1406
- Displayed Date：2023/04/25 19:00
- Category： Others
When I saved RAS information in a file during the fault diagnosis of the SX, files with '.RAS' and '.BSM' extensions were created and I don't know ...

The '.BSM' file is intended for manufacturers' maintenance purposes. You can check fault information by opening the '.RAS' file with Notepad or another tex... Show Detail
- No：1608
- Displayed Date：2023/04/25 19:00
- Category： Support tool