The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_

The specified current value is constant regardless of the frequency because the input impedance for the pulse input I/F

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective va

Unless you register the module in the system definition and set the I/O group in the CPU parameters, data monitoring is

It is not provided as internal memory. You need to create the circuit shown in the attached diagram. The example shows a

You should be careful because if the write protection is OFF, the ROM is rewritten simultaneously with the internal RAM

In the system definition, group-type slave stations in any I/O configuration are registered as 'DeviceNet capsule.' In a

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes p

It depends on your CPU model and how often you conduct regular inspection. The backup time after a battery error is det

An unused slot is permitted in a system configuration. If you plan to mount a module in the unused slot in the future,

Search by category

Keyword Search

FAQ within [ PLC ]

91-100 of Total 398

≪ 10 / 40page ≫

I use the high-speed counter module (Type_ NP1F-HC□). The user's manual (FEH210) shows 'Multiplication function_ x1, x4.' How can I switch between ...

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_ ･ Forward pulse + Reverse pulse_ x1 ... Show Detail
- No：1564
- Displayed Date：2023/04/25 19:00
- Category： Function
I heard that the high-speed counter module (Type_ NP1F-HC2) requires a current value less than 40 mA for frequencies up to 50 kHz.

The specified current value is constant regardless of the frequency because the input impedance for the pulse input I/F is fixed. Show Detail
- No：1571
- Displayed Date：2023/04/25 19:00
- Category： Function
In PPID, a POU for the PID FB package, which range does the % of proportional band P account for?

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective variation range from 0 to 100%. It is... Show Detail
- No：1580
- Displayed Date：2023/04/25 19:00
- Category： Function
Does data monitoring of the I/O area require the module to be registered in the system definition?

Unless you register the module in the system definition and set the I/O group in the CPU parameters, data monitoring is disabled because no memory is reserve... Show Detail
- No：1581
- Displayed Date：2023/04/25 19:00
- Category： Support tool
I create a program for the SPH by using the Standard Loader (Type_ NP4H-SWN). Is flicker relay memory available?

It is not provided as internal memory. You need to create the circuit shown in the attached diagram. The example shows a circuit in which M0 repeats ON and O... Show Detail
- No：1605
- Displayed Date：2023/04/25 19:00
- Category： Application
When I mount the user ROM card for the SPH200 (Type_ NP8PMF-16) without changing its write protection from OFF, is the content of the ROM protected?

You should be careful because if the write protection is OFF, the ROM is rewritten simultaneously with the internal RAM of the CPU during program download. Show Detail
- No：1617
- Displayed Date：2023/04/25 19:00
- Category： Main unit
I use DeviceNet interface module (NP1L-RD1) under DeviceNet master (NP1L-DN1). How can I specify NP1L-RD1 in the system definition?

In the system definition, group-type slave stations in any I/O configuration are registered as 'DeviceNet capsule.' In addition, the numbers of input and out... Show Detail
- No：1644
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I use an Ethernet module (Type_ NP1L-ET1/ET2) to read/write data from/to a PC in the loader command communication mode. At what time are data read ...

(1) Standard CPU_ Access takes place when tasks end (synchronized with tasks). (2) High-performance CPU_ Access takes place when a request is generated rega... Show Detail
- No：1300
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
With the MICREX-SX SPH Series, when should I replace the battery after the battery error LED of the CPU module lights up?

It depends on your CPU model and how often you conduct regular inspection. The backup time after a battery error is detected is as follows. NP1PS-32/32R:... Show Detail
- No：1312
- Displayed Date：2023/04/25 19:00
- Category： Accessory
Is it permitted to have an unused slot in an SPH system configuration?

An unused slot is permitted in a system configuration. If you plan to mount a module in the unused slot in the future, it can be registered as 'unimplemen... Show Detail
- No：1313
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 14:32
- Category： Main unit