The LG terminal is a line filter ground terminal in the power supply module. It is intended for guiding any external noi

Since the primary battery built in the SPF main unit cannot be replaced, the battery connection switch is set to off at

When the FALDIC-α se

Yes, there is a difference in system operation when control power supply for a servo amplifier is shut down. The ALPHA5

The following loader software and adapter are required. 1) Loader software ・NP4H-SWN The product CD of NP4H-SWN in

The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each

This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed c

The following devices are necessary to connect a personal computer loader and a MICREX-F series PLC: a loader adapter FL

It depends on your CPU model and how often you conduct regular inspection. The backup time after a battery error is det

The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the sys

If the project that you want to upload includes expansion FBs provided by Fuji Electric, the expansion FBs must be insta

Search by category

Keyword Search

FAQ within [ PLC ]

1-10 of Total 398

≪ 1 / 40page ≫

What is the difference between the LG and FG terminals of the power supply module (Type_ NP1S-22)?

The LG terminal is a line filter ground terminal in the power supply module. It is intended for guiding any external noise produced in the power supply or sw... Show Detail
- No：1374
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 10:52
- Category： Main unit
Newly purchased SPF shows Battery error. How can I solve it ?

Since the primary battery built in the SPF main unit cannot be replaced, the battery connection switch is set to off at the factory shipment. By turning on t... Show Detail
- No：1525
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
When the FALDIC-α series is replaced with the ALPHA5 series or later, is there a difference in 'fail-soft operation' of each servo amplifier connec...

Yes, there is a difference in system operation when control power supply for a servo amplifier is shut down. The ALPHA5 series or later supports the MICREX-... Show Detail
- No：1503
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:39
- Category： Function
I would like to read and write programs of the MICREX-F series on a personal computer (Windows 10). What loader software and connection cable are r...

The following loader software and adapter are required. 1) Loader software ・NP4H-SWN The product CD of NP4H-SWN includes the loader software 'MICREX... Show Detail
- No：1456
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:23
- Category： Support tool (Others)
I understand that the high-speed counter module (Type_ NP1F-HC2MR) is capable of counting pulses of 5 V/12 V/24 V. Is it possible to count with a d...

The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each channel. To set the signal level, s... Show Detail
- No：1398
- Displayed Date：2023/04/25 19:00
- Category： Function
I have connected the SPH Series with the POD (UG Series) via the T-link. A code F8 is displayed on the screen of the POD. What is a possible cause?

This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed contact on the POD (UG), (3) Improp... Show Detail
- No：1559
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
I want to use a personal computer loader with a MICREX-F series PLC.

The following devices are necessary to connect a personal computer loader and a MICREX-F series PLC: a loader adapter FLT-ASFKA (or FLT-ASFK), and a USB cab... Show Detail
- No：1459
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 09:37
- Category： Support tool (Others)
With the MICREX-SX SPH Series, when should I replace the battery after the battery error LED of the CPU module lights up?

It depends on your CPU model and how often you conduct regular inspection. The backup time after a battery error is detected is as follows. NP1PS-32/32R:... Show Detail
- No：1312
- Displayed Date：2023/04/25 19:00
- Category： Accessory
A nonfatal fault of the takt cycle monitoring error has occurred. What is a possible cause?

The takt cycle monitoring error is caused by the following factors_ (1) The preset takt cycle value specified in the system definition is shorter than the ac... Show Detail
- No：1576
- Displayed Date：2023/04/25 19:00
- Category： Error
When uploading a project from CPU, the error message 'Ex.FB that import is done was not found. Import the Ex.FB using the program import function' ...

If the project that you want to upload includes expansion FBs provided by Fuji Electric, the expansion FBs must be installed on your computer. Install the ex... Show Detail
- No：1662
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)