-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I creat user FB in StandardV3, and defined input/output parameter as word (WV). Can I directly access any bit within this parameter WV?
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- We share the D300win and other PLC engineering tool software among several people. Do we need to purchase the software for each person?
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
GLOBAL
Search by category
Keyword Search
FAQ within [ PLC ]
-
The error occurs because the address display mode is set to 'FLEX-PC,' but the address representation of the word device is not hexadecimal. For the addres... Show Detail
- No：1496
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
-
This is because the SX bus loop-back plug is not connected. Connect a loop-back plug to the base board. Show Detail
- No：1335
- Displayed Date：2023/04/25 19:00
- Category： Error
-
What standards does the MICREX-SX series comply with?
Fuji Electric website provides information on the standards that the MICREX-SX series complies with. Visit the following URL. Show Detail
- No：1358
- Displayed Date：2023/04/25 19:00
- Category： Others
-
They are retained. Note, however, that they are cleared if the power of the FL-net module is turned off. Show Detail
- No：1405
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
When SX-Programmer Expert (D300win) was upgraded to V3.3.2.0, the 'IP address and gateway setting definition' was added to accommodate the function addition ... Show Detail
- No：1417
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
-
When using Cfr32, are the start code, end code, and BCC included in the maximum data size?
Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies to _Cfr64, _Cfr128, _Cfr252, and _Cfr... Show Detail
- No：1495
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
When replacing SPB (N mode) with SPF, can I use the program without change?
SPF does not support N mode. Therefore, to use the program of SPB (N mode) in SPF, you need to convert it. Refer to the following manual for how to conve... Show Detail
- No：1518
- Displayed Date：2023/04/25 19:00
- Category： Application
-
Yes, a CPU is necessary. In the case of a system with no CPU, the input status LED does not work even if signals are externally input into the input module. Show Detail
- No：1537
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed contact on the POD (UG), (3) Improp... Show Detail
- No：1559
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
-
The '*' symbol on the ladder bus indicates a circuit being changed online. It will disappear when you transfer the changed circuit to the PLC. Show Detail
- No：1609
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
1-10 of Total 398