-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I use the Ethernet module (NP1L-ET1), can I use a same message port No. (SPORT_NO) to establish multiple connections (use multiple M_OPEN)?
- I use the Ethernet module (NP1L-ET1/ET2) and using communication FB (M_OPEN). M_OPEN sets two ports of RPORT_NO and SPORT_NO. Does this mean that o...
- When I forget the IP address of the WEB module (Type_ NP1L-WE1), can I change the IP from an external network?
- During loader command communication of Ethernet, a port is closed after it has not been accessed from a personal computer for a certain period of t...
- I use the Ethernet module (Type_NP1L-ET1). Is the IP address assigned automatically?
GLOBAL
Search by category
Keyword Search
FAQ within [ Communication (Ethernet) ]
-
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?
Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
-
What is necessary for MODBUS_TCP communication between SPH and an external device?
The following are necessary. 1) Hardware Ethernet interface module (NP1L-ET1) or CPU module with built-in Ethernet (SPH2000/3000 series CPU types w... Show Detail
- No：1470
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:30
-
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?
Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
-
One M_OPEN consumes one port of SPORT_NO, which is the local port. RPORT_NO is the port of the other end of the communication seen from the SX. Show Detail
- No：1643
- Displayed Date：2023/04/25 19:00
-
The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported. Show Detail
- No：1442
- Displayed Date：2023/04/25 19:00
-
Can I perform broadcast communication between CPU modules without using FL-net or P/PE-link module?
The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with built-in Ethernet, you can build a bro... Show Detail
- No：1485
- Displayed Date：2023/04/25 19:00
-
Yes, it is the same. Show Detail
- No：1377
- Displayed Date：2023/04/25 19:00
-
No, you can't. You can check the IP address by connecting the PC loader to the CPU module and monitoring the RAS information of the fault diagnosis function. Show Detail
- No：1616
- Displayed Date：2023/04/25 19:00
-
In the parameter setting of the Ethernet module in the system definition, set the 'Server FTP command watch timer value' to 0. The port is not closed even if... Show Detail
- No：1612
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:59
-
No, the Ethernet module does not support the AUTO-MDI/MDIX function (Auto-switching of straight/cross cable.) The applicable cable type depends on whether ... Show Detail
- No：1562
- Displayed Date：2023/04/25 19:00
1-10 of Total 25