-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I use the Ethernet module (NP1L-ET1), can I use a same message port No. (SPORT_NO) to establish multiple connections (use multiple M_OPEN)?
- I use the Ethernet module (NP1L-ET1/ET2) and using communication FB (M_OPEN). M_OPEN sets two ports of RPORT_NO and SPORT_NO. Does this mean that o...
- When I forget the IP address of the WEB module (Type_ NP1L-WE1), can I change the IP from an external network?
- During loader command communication of Ethernet, a port is closed after it has not been accessed from a personal computer for a certain period of t...
- I use the Ethernet module (Type_NP1L-ET1). Is the IP address assigned automatically?
GLOBAL
Search by category
Keyword Search
FAQ within [ Communication (Ethernet) ]
-
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?
Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
-
The amounts of data transmitted or received are not limited as R_WRITE instruction/R_READ instruction but by the capacity of the memory from/to which data ar... Show Detail
- No：1324
- Displayed Date：2023/04/25 19:00
-
The redundant function of the SPH Series provides redundancy only for the CPU and it cannot make the Ethernet redundant. Show Detail
- No：1392
- Displayed Date：2023/04/25 19:00
-
No, the Ethernet module does not support the AUTO-MDI/MDIX function (Auto-switching of straight/cross cable.) The applicable cable type depends on whether ... Show Detail
- No：1562
- Displayed Date：2023/04/25 19:00
-
I use the Ethernet module (Type_NP1L-ET1). Is the IP address assigned automatically?
The IP address is not assigned automatically. (DHCP function is not supported.) The default IP address is '192.168.0.1'. You can check the IP address b... Show Detail
- No：1595
- Displayed Date：2023/04/25 19:00
-
It is not possible for the user to restore the factory setting. The module will have to be returned to the factory for initialization for a fee. Contact ou... Show Detail
- No：1409
- Displayed Date：2023/04/25 19:00
-
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?
Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
-
Is broadcast communication via Ethernet possible?
It is possible as long as the protocol is UDP/IP. In the M_OPEN FB, specify 255.255.255.255 as the IP address to be set for the 'communication destination s... Show Detail
- No：1415
- Displayed Date：2023/04/25 19:00
-
Can I perform broadcast communication between CPU modules without using FL-net or P/PE-link module?
The general-purpose communication function of Ethernet allows simplified broadcast communication. By using a CPU with built-in Ethernet, you can build a bro... Show Detail
- No：1485
- Displayed Date：2023/04/25 19:00
-
What is necessary for MODBUS_TCP communication between SPH and an external device?
The following are necessary. 1) Hardware Ethernet interface module (NP1L-ET1) or CPU module with built-in Ethernet (SPH2000/3000 series CPU types w... Show Detail
- No：1470
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:30
1-10 of Total 25