-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I use the Ethernet module (NP1L-ET1), can I use a same message port No. (SPORT_NO) to establish multiple connections (use multiple M_OPEN)?
- I use the Ethernet module (NP1L-ET1/ET2) and using communication FB (M_OPEN). M_OPEN sets two ports of RPORT_NO and SPORT_NO. Does this mean that o...
- When I forget the IP address of the WEB module (Type_ NP1L-WE1), can I change the IP from an external network?
- During loader command communication of Ethernet, a port is closed after it has not been accessed from a personal computer for a certain period of t...
- I use the Ethernet module (Type_NP1L-ET1). Is the IP address assigned automatically?
GLOBAL
Search by category
Keyword Search
FAQ within [ Communication (Ethernet) ]
-
The redundant function of the SPH Series provides redundancy only for the CPU and it cannot make the Ethernet redundant. Show Detail
- No：1392
- Displayed Date：2023/04/25 19:00
-
How many units of Ethernet module (Type_ NP1L-ET□) can be used in a system?
Up to 4 units can be connected in 1 configuration (on 1 SX bus). Note, however, that they must be configured so that the total number of units of other comm... Show Detail
- No：1395
- Displayed Date：2023/04/25 19:00
-
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?
Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
-
The IP address and port standard No. of the self station of the Ethernet module are stored in the internal ROM of the Ethernet module. After replacing an Eth... Show Detail
- No：1590
- Displayed Date：2023/04/25 19:00
-
It is not possible for the user to restore the factory setting. The module will have to be returned to the factory for initialization for a fee. Contact ou... Show Detail
- No：1409
- Displayed Date：2023/04/25 19:00
-
Is broadcast communication via Ethernet possible?
It is possible as long as the protocol is UDP/IP. In the M_OPEN FB, specify 255.255.255.255 as the IP address to be set for the 'communication destination s... Show Detail
- No：1415
- Displayed Date：2023/04/25 19:00
-
No, you can't. You can check the IP address by connecting the PC loader to the CPU module and monitoring the RAS information of the fault diagnosis function. Show Detail
- No：1616
- Displayed Date：2023/04/25 19:00
-
Yes, it is the same. Show Detail
- No：1377
- Displayed Date：2023/04/25 19:00
-
The file transfer error occurs because the module driver is downloaded with the Ethernet module not recognized by the CPU. For the CPU to recognize the Ethe... Show Detail
- No：1404
- Displayed Date：2023/04/25 19:00
-
The Loader command mode is fixed to the TCP/IP communication. UDP/IP communication is not supported. Show Detail
- No：1442
- Displayed Date：2023/04/25 19:00
11-20 of Total 25