No, it is not possible. Combine the electronic cam FB package (Type_ NP4N-CAMFV3) with a positioning control module (Typ

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). T

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always c

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with po

Possible causes include a fuse blowout in the high-speed output module (Type_ NP1Y32T09P1-A).

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_

No, it is not possible. Use an encoder of the line-driver or open-collector output type. When using a line-driver type,

The purpose of a dummy module is to use it as a temporary replacement of an I/O module that has been defined with the sy

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mism

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1)

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

21-30 of Total 50

≪ 3 / 5page ≫

Is electronic cam operation possible without using the dedicated module?

No, it is not possible. Combine the electronic cam FB package (Type_ NP4N-CAMFV3) with a positioning control module (Type_ NP1F-MP2/MA2). Show Detail
- No：1334
- Displayed Date：2023/04/25 19:00
How long is the refresh cycle of the pulse count value data of the high-speed counter module (Type_ NP1F-HC2)?

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). The count data, however, will be refle... Show Detail
- No：1547
- Displayed Date：2023/04/25 19:00
When I turned on the positioning control module (Type_ NP1F-MP2/MA2) in the morning, the parameters were reset to the initial values. What is the f...

Since the parameter data area of the positioning control module (Type_ NP1F-MP2/MA2) operates on the RAM, it is always cleared when you turn off the module. ... Show Detail
- No：1573
- Displayed Date：2023/04/25 19:00
When the pulse catch function of the high-speed input module (Type_ NP1X3206-A) is used, can all points be used? Is any difference made to the puls...

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with ports 1 to 8. With ports 9 to 32, pu... Show Detail
- No：1321
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
On the high-speed output module (Type_ NP1Y32T09P1-A), the ONL/ERR lamps are illuminated. Why does this happen?

Possible causes include a fuse blowout in the high-speed output module (Type_ NP1Y32T09P1-A). Show Detail
- No：1342
- Displayed Date：2023/04/25 19:00
I use the high-speed counter module (Type_ NP1F-HC□). The user's manual (FEH210) shows 'Multiplication function_ x1, x4.' How can I switch between ...

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_ ･ Forward pulse + Reverse pulse_ x1 ... Show Detail
- No：1564
- Displayed Date：2023/04/25 19:00
Is it possible to use an encoder of the complementary output type for the high-speed counter module (Type_ NP1F-HC2)?

No, it is not possible. Use an encoder of the line-driver or open-collector output type. When using a line-driver type, pay attention to the output capacity ... Show Detail
- No：1320
- Displayed Date：2023/04/25 19:00
I cannot register a dummy module (Type_ NP1F-DMY) with the system definitions using the loader.

The purpose of a dummy module is to use it as a temporary replacement of an I/O module that has been defined with the system but does not actually exist for ... Show Detail
- No：1348
- Displayed Date：2023/04/25 19:00
What is the dummy module (Type_ NP1F-DMY) used for? Is it required for an unused slot?

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mismatch.' In a case like this, a dummy ... Show Detail
- No：1349
- Displayed Date：2023/04/25 19:00
I use the pulse train output positioning control module (Type_ NP1F-HP2). Please tell me the rated voltage/current of the pulse output and control ...

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1) Pulse output_ 30 V DC, 40 mA or less... Show Detail
- No：1602
- Displayed Date：2023/04/25 19:00