Pulse input type_ A-phase for the pulse and B-phase for the sign.

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with po

Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of

The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each

If the start bit remains on, the positioning end signal is not generated.

You can check it with the status indication LED on the front of the module. When a low battery voltage is detected, the

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1)

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mism

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare v

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

1-10 of Total 50

≪ 1 / 5page ≫

With the multi-channel high-speed counter module (Type_ NP1F-HC8), how can a single-phase pulse be received?

Pulse input type_ A-phase for the pulse and B-phase for the sign. Show Detail
- No：1366
- Displayed Date：2023/04/25 19:00
When the pulse catch function of the high-speed input module (Type_ NP1X3206-A) is used, can all points be used? Is any difference made to the puls...

Yes, all points can be used. Regarding the pulse width, pulse signals with a width down to 20 us can be captured with ports 1 to 8. With ports 9 to 32, pu... Show Detail
- No：1321
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:17
Which is the signal that indicates pulse output completion on the positioning control module (Type_ NP1F-MP2)?

Pulse output completion is indicated by the 'Command pulse zero' signal. Normally, it is '1' to indicate the status of completion. When the number of pulses... Show Detail
- No：1548
- Displayed Date：2023/04/25 19:00
I understand that the high-speed counter module (Type_ NP1F-HC2MR) is capable of counting pulses of 5 V/12 V/24 V. Is it possible to count with a d...

The module is equipped with 2 channels of high-speed counter and signals of a different voltage can be counted for each channel. To set the signal level, s... Show Detail
- No：1398
- Displayed Date：2023/04/25 19:00
With the pulse train output positioning control module (Type_ NP1F-HP2), positioning has ended but the end signal is not generated.

If the start bit remains on, the positioning end signal is not generated. Show Detail
- No：1317
- Displayed Date：2023/04/25 19:00
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

You can check it with the status indication LED on the front of the module. When a low battery voltage is detected, the CER LED on the front of the module ... Show Detail
- No：1620
- Displayed Date：2023/04/25 19:00
I use the pulse train output positioning control module (Type_ NP1F-HP2). Please tell me the rated voltage/current of the pulse output and control ...

Both the pulse output and control output are open collector outputs. They should be used within the following ranges (1) Pulse output_ 30 V DC, 40 mA or less... Show Detail
- No：1602
- Displayed Date：2023/04/25 19:00
What is the dummy module (Type_ NP1F-DMY) used for? Is it required for an unused slot?

In an SX system, removing any I/O module that has failed causes the CPU to stop running due to a 'system definition mismatch.' In a case like this, a dummy ... Show Detail
- No：1349
- Displayed Date：2023/04/25 19:00
I use the high-speed counter module (Type_ NP1F-HC2) FB. The compare value is larger than the present counter value but the compare output becomes ...

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare value is written by turning the data w... Show Detail
- No：1309
- Displayed Date：2023/04/25 19:00
When I use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A), can I set software filters?

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A). Show Detail
- No：1599
- Displayed Date：2023/04/25 19:00

1-10 of Total 50

Info & News

To Top of Page

PKSHA FAQ logo

Function

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability