Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected.

Check the feedback pulse wiring (to make sure that a shielded twisted pair is used, wiring conditions are appropriate, e

The high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) cannot be mounted on the T

The specified current value is constant regardless of the frequency because the input impedance for the pulse input I/F

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used.

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective va

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare v

Pulse input type_ A-phase for the pulse and B-phase for the sign.

The four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) does not have a physical ±OT terminal. You can s

The module counts feedback pulses even without Z-phase pulse signals. Note that when Z-phase pulse signals are not prov

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Function

Latest FAQ

When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
When I switch the CPU module from RUN to STOP while the four-axis pulse output unit (NR1SF-HP4DT) is outputting pulses, does the positioning operat...
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...
What is the difference between the PID forward and backward operations when the PID FB package is used?
How can I detect a low battery voltage of the SRAM card with the memory card interface module (Type_ NP1F-MM1)?

GLOBAL

Search by category

Keyword Search

FAQ within [ Function ]

1-10 of Total 50

≪ 1 / 5page ≫

I want to run an external device by pulse output with the high-speed output module (Type_ NP1Y32T09P1-A). What are the points to note regarding the...

Note the following points (1) The rated output voltage is 12 to 24 V. Check the voltage of the device to be connected. (2) The Z-phase/timing input signal f... Show Detail
- No：1399
- Displayed Date：2023/04/25 19:00
The current feedback value of the positioning control module (Type_ NP1F-MP2) changes even when the CPU module (Type_ NP1P*-***) is stopped. What c...

Check the feedback pulse wiring (to make sure that a shielded twisted pair is used, wiring conditions are appropriate, etc.). One possible reason for the c... Show Detail
- No：1421
- Displayed Date：2023/04/25 19:00
Can I mount the high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) on the T-link expansion (RT1)?

The high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) cannot be mounted on the T-link expansion (RT1). Show Detail
- No：1433
- Displayed Date：2023/04/25 19:00
I heard that the high-speed counter module (Type_ NP1F-HC2) requires a current value less than 40 mA for frequencies up to 50 kHz.

The specified current value is constant regardless of the frequency because the input impedance for the pulse input I/F is fixed. Show Detail
- No：1571
- Displayed Date：2023/04/25 19:00
How can I provide Z-phase pulses when the equipment connected with the positioning control module (Type_ NP1F-MP2/MA2) uses a stepping motor?

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
In PPID, a POU for the PID FB package, which range does the % of proportional band P account for?

Proportional band P is the % of the variation range of input PV required for the change of output MV in the effective variation range from 0 to 100%. It is... Show Detail
- No：1580
- Displayed Date：2023/04/25 19:00
I use the high-speed counter module (Type_ NP1F-HC2) FB. The compare value is larger than the present counter value but the compare output becomes ...

One possibility is that the compare value is not stored in the compare register of the high-speed counter. The compare value is written by turning the data w... Show Detail
- No：1309
- Displayed Date：2023/04/25 19:00
With the multi-channel high-speed counter module (Type_ NP1F-HC8), how can a single-phase pulse be received?

Pulse input type_ A-phase for the pulse and B-phase for the sign. Show Detail
- No：1366
- Displayed Date：2023/04/25 19:00
I want to connect wiring for ±OT input with the four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) but the unit does not have the te...

The four-axis pulse string output terminal module (Type_ NR1SF-HP4DT) does not have a physical ±OT terminal. You can solve this problem by using software a... Show Detail
- No：1447
- Displayed Date：2023/04/25 19:00
The feedback pulses of the pulse train duplex positioning control module (Type_ NP1F-MP2) have A and B phases only and do not have Z-phase pulses. ...

The module counts feedback pulses even without Z-phase pulse signals. Note that when Z-phase pulse signals are not provided, origin return operation is dis... Show Detail
- No：1549
- Displayed Date：2023/04/25 19:00

1-10 of Total 50

Info & News

To Top of Page

PKSHA FAQ logo

Function

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability