-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- I have configured a multi-CPU system, but the system has run out of memory for the multi-CPU. Can I access the common general memory from the other...
- What is the rated current value of the fuse in the power supply module (NP1S-22)? I want to know to select the circuit breaker on the primary side ...
- When I mount the user ROM card for the SPH200 (Type_ NP8PMF-16) without changing its write protection from OFF, is the content of the ROM protected?
- When the retain memory (memory for data backup with a battery) of the CPU module of the MICREX-SX Series SPH is corrupted, how does the CPU module ...
- Can I mount or remove a CPU module and a power supply module on a hot plug base board while the system power is on?
GLOBAL
Search by category
Keyword Search
FAQ within [ Main unit ]
-
Since the data equalization (data copying from the operating CPU to the standby CPU) is performed after the default task is processed, the larger the size of... Show Detail
- No：1568
- Displayed Date：2023/04/25 19:00
-
Check the following system memory. (1) Configuration information %MW10.52 to %MW10.67 (WSM52 to 67) (2) Configuration fault information %MW10.68 to %MW1... Show Detail
- No：1482
- Displayed Date：2023/04/25 19:00
-
The P-link memory is prepared in the P-link module. It is separate from the memory in the CPU and no change takes place at the time of switchover to a standb... Show Detail
- No：1343
- Displayed Date：2023/04/25 19:00
-
When the power supply recovers to normal, the ALM contact automatically returns to the original position (open). Show Detail
- No：1289
- Displayed Date：2023/04/25 19:00
-
When the memory with a retain attribute is corrupted, the CPU clears the memory and operates in nonfatal fault condition. If the power is reset again in this... Show Detail
- No：1611
- Displayed Date：2023/04/25 19:00
-
The SPH does not have a RUN contact. Is there any alternative?
As an alternative, you can combine hardware and software functions. (1) Hardware_ Prepare a relay output card and use one point as a RUN contact. (2) Sof... Show Detail
- No：1587
- Displayed Date：2023/04/25 19:00
-
When you use battery-less operation on the SPH, is the history of RAS information recorded?
During battery-less operation, previous fault information and other 'history of RAS' are not saved. Only the present RAS information is displayed. Show Detail
- No：1579
- Displayed Date：2023/04/25 19:00
-
Can I store multiple programs in the user ROM card (CF or SD) ?
No, it is not possible. Only one program can be stored. Show Detail
- No：1298
- Displayed Date：2023/04/25 19:00
-
No, they do not have polarity because they use relay contacts. Show Detail
- No：1585
- Displayed Date：2023/04/25 19:00
-
No, it doesn't. A power supply module may occupy two slots (Type_ NP1S-22, NP1S-42) or one slot (Type_ NP1S-81, NP1S-91). The connector at the far left... Show Detail
- No：1340
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:34
21-30 of Total 34