No, there isn't. Receive the external power supply as an external input to detect the status.

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redu

Clock adjustment is initiated from CPU0 (operating) to other CPUs (standby). It takes place on a constant (1-minute) cyc

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the begi

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without tu

The SX bus station number for the slot on which the CPU module is mounted is recognized as unused.

For an alarm contact output of an error of the PLC system, select an arbitrary output module in the system definitions a

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the syste

A user ROM card can be inserted and removed when the UROM LED is not illuminated (the key switch is set to a position ot

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH > Main unit

Latest FAQ

I have configured a multi-CPU system, but the system has run out of memory for the multi-CPU. Can I access the common general memory from the other...
What is the rated current value of the fuse in the power supply module (NP1S-22)? I want to know to select the circuit breaker on the primary side ...
When I mount the user ROM card for the SPH200 (Type_ NP8PMF-16) without changing its write protection from OFF, is the content of the ROM protected?
When the retain memory (memory for data backup with a battery) of the CPU module of the MICREX-SX Series SPH is corrupted, how does the CPU module ...
Can I mount or remove a CPU module and a power supply module on a hot plug base board while the system power is on?

GLOBAL

Search by category

Keyword Search

FAQ within [ Main unit ]

11-20 of Total 34

≪ 2 / 4page ≫

Is there an RAS that detects an error of the external power supply used for an I/O module?

No, there isn't. Receive the external power supply as an external input to detect the status. Show Detail
- No：1388
- Displayed Date：2023/04/25 19:00
A CPU module has a rotary switch (0 to F) for setting the CPU No. on its front. What CPU No. should I set?

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redundant system which uses multiple CPU ... Show Detail
- No：1504
- Displayed Date：2023/04/25 19:00
Does equalization (from an operating CPU to a standby CPU) of the internal clock take place automatically? If so, when does it take place?

Clock adjustment is initiated from CPU0 (operating) to other CPUs (standby). It takes place on a constant (1-minute) cycle at the time of and after system st... Show Detail
- No：1401
- Displayed Date：2023/04/25 19:00
How does the redundant system handle tasks being executed when the operation is switched from an operating CPU to a standby CPU?

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the beginning of the task. Show Detail
- No：1530
- Displayed Date：2023/04/25 19:00
When redundant CPUs mounted on the same base board break down, can I replace the CPU without turning off the power?

If the CPU modules are mounted on a hot plug base board with station No. setup function, you can replace them without turning off the power. Show Detail
- No：1367
- Displayed Date：2023/04/25 19:00
What will happen to the station number assigned to each slot of a base board with a station number setting switch (Type_ NP1BS-**S, NP1BP-13S, NP1B...

The SX bus station number for the slot on which the CPU module is mounted is recognized as unused. Show Detail
- No：1382
- Displayed Date：2023/04/25 19:00
Is there an alarm output contact to use when an error occurs in the PLC system?

For an alarm contact output of an error of the PLC system, select an arbitrary output module in the system definitions and define its 0th bit as a 'system DO... Show Detail
- No：1347
- Displayed Date：2023/04/25 19:00
Can I use a base board with station No. setup function (Type_ NP1B*-**S) as a standard base board (without 'S' at the end of type code)?

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the system definition of the loader designed f... Show Detail
- No：1531
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:50
Can I remove user ROM card in the CPU module (CF or SD) while the CPU is running?

A user ROM card can be inserted and removed when the UROM LED is not illuminated (the key switch is set to a position other than UROM). When removing it whi... Show Detail
- No：1304
- Displayed Date：2023/04/25 19:00
What is the rated current value of the fuse in the power supply module (NP1S-22)? I want to know to select the circuit breaker on the primary side ...

The rated current is 3 A. Show Detail
- No：1641
- Displayed Date：2023/04/25 19:00

11-20 of Total 34

Info & News

To Top of Page

PKSHA FAQ logo

Main unit

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability