-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
What is the difference between the LG and FG terminals of the power supply module (Type_ NP1S-22)?
The LG terminal is a line filter ground terminal in the power supply module. It is intended for guiding any external noise produced in the power supply or sw... Show Detail
- No：1374
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 10:52
- Category： Main unit
-
It is possible with the Ethernet module software version V36 or later by using the F_READ (read)/F_WRITE (write) FB. After writing, the power (or reset) o... Show Detail
- No：1370
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:42
- Category： Communication (Ethernet)
-
Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
- Category： Function
-
What is the difference between RS-485 and RS-422 ?
RS-485 is upper compatible with RS-422. In general, RS-422 devices mainly use 4-wire connection method, while RS-485 devices mainly use 2-wire connection met... Show Detail
- No：1521
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
There is a possibility of mismatch between the project in the user ROM card and the CPU memory. On the 'Failure diagnosis' dialog, check the 'Resource inform... Show Detail
- No：1660
- Displayed Date：2023/04/25 19:00
- Category： Support tool
-
Yes, it is possible. Of the parameter setting items of initialization, changes made to specific parameter items (such as frame detection, code conversion and... Show Detail
- No：1639
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
You don't need a dedicated cable. Since the parameters will be set via the CPU module, you need a loader cable for the PLC and the program loader software. Show Detail
- No：1676
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
It enables reception only when CD (Carrier Detection) is ON. (Other operations are the same as those in the DTE mode.) Show Detail
- No：1598
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
While NP1F-HC2 requires an external power supply of 5 V DC, NP1F-HC8 produces 5 V DC within the module from an external 24 V DC power supply and does not req... Show Detail
- No：1341
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The received data is cleared to 0. Therefore, be sure not to read (ignore) the data by application program. Reopening the FB (turning the 'OPEN' terminal fro... Show Detail
- No：1672
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
1-10 of Total 235