The high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) cannot be mounted on the T

Selecting the DCE mode for the communication parameter_ DCE designation keeps DSR always on.

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in th

The purpose of a dummy module is to use it as a temporary replacement of an I/O module that has been defined with the sy

Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used.

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for th

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_

The existing MICREX-F program does not need any modification.

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

1-10 of Total 235

≪ 1 / 24page ≫

Can I mount the high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) on the T-link expansion (RT1)?

The high-speed output module (Type_ NP1Y32T09P1-A)/high-speed input module (Type_ NP1X3206-A) cannot be mounted on the T-link expansion (RT1). Show Detail
- No：1433
- Displayed Date：2023/04/25 19:00
- Category： Function
When does the port status_ DSR (data set ready) in a structure variable_ RAS of the non-procedural standard expansion FB for communication remain on?

Selecting the DCE mode for the communication parameter_ DCE designation keeps DSR always on. Show Detail
- No：1297
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
In the P/PE link area, is the send area of the local station cleared when the power supply is turned off once and turned on again? Is there any set...

The area is cleared when the power supply is turned off once and turned on again. The P/PE link memory is located in the built-in memory (RAM) of the P/PE-l... Show Detail
- No：1436
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I cannot register a dummy module (Type_ NP1F-DMY) with the system definitions using the loader.

The purpose of a dummy module is to use it as a temporary replacement of an I/O module that has been defined with the system but does not actually exist for ... Show Detail
- No：1348
- Displayed Date：2023/04/25 19:00
- Category： Function
When using Cfr32, are the start code, end code, and BCC included in the maximum data size?

Yes, they are. The maximum size is 32 words including the actual data, start code, end code, and BCC. (The same applies to _Cfr64, _Cfr128, _Cfr252, and _Cfr... Show Detail
- No：1495
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
How can I provide Z-phase pulses when the equipment connected with the positioning control module (Type_ NP1F-MP2/MA2) uses a stepping motor?

Use the 'Excitation timing output' signal for the Z-phase pulse when a stepping motor is used. Show Detail
- No：1574
- Displayed Date：2023/04/25 19:00
- Category： Function
I understand that an analog input module (Type_ NP1AXH4-MR, etc.) has a signal line breakage detection function. How does it work?

For an analog input range (1 to 5 V or 4 to 20 mA), a line breakage detection function is provided. An input voltage of 0.92 V or lower for the 1 to 5 V ran... Show Detail
- No：1316
- Displayed Date：2023/04/25 19:00
- Category： I/O
For the initial setting of a general-purpose communication module with only one communication port such as NP1L-RS2 and NP1L-RS4, is it correct to ...

Set the port No. as described below. (1) For NP1L-RS2_ Set '0.' (2) For NP1L-RS4_ Set '1.' See the figure below for the setting for each type of genera... Show Detail
- No：1383
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/13 15:45
- Category： Communication (Others)
I use the high-speed counter module (Type_ NP1F-HC□). The user's manual (FEH210) shows 'Multiplication function_ x1, x4.' How can I switch between ...

The multiplication of the high-speed counter module is automatically set as follows depending on the input pulse form_ ･ Forward pulse + Reverse pulse_ x1 ... Show Detail
- No：1564
- Displayed Date：2023/04/25 19:00
- Category： Function
An existing P-link system is composed of MICREX-F. If part of it is replaced with P-link of MICREX-SX, does the existing MICREX-F program need to b...

The existing MICREX-F program does not need any modification. Show Detail
- No：1319
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)

1-10 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability