The simulation function of the StandardV3 does not support the index register. Check the program operation using a har

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the begi

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the syste

The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment,

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one

In exponentiation operation, when a negative value is used for the base, the result is 0.

A 'client' is a device that collects data. Since the PLC is a device from which data is collected, there is no OPC clien

The specified current value is constant regardless of the frequency because the input impedance for the pulse input I/F

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

81-90 of Total 235

≪ 9 / 24page ≫

I converted an M/F program into an SX program with the Standard loader. I performed simulation of the converted program in the Standard loader, but...

The simulation function of the StandardV3 does not support the index register. Check the program operation using a hardware PLC. Show Detail
- No：1471
- Displayed Date：2023/04/25 19:00
- Category： Support tool (Standard)
Can I use both P-link and PE-link in one system?

No, you cannot. Show Detail
- No：1523
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
How does the redundant system handle tasks being executed when the operation is switched from an operating CPU to a standby CPU?

The equivalent data is retained for one default task during switching and the standby CPU starts execution from the beginning of the task. Show Detail
- No：1530
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Can I use a base board with station No. setup function (Type_ NP1B*-**S) as a standard base board (without 'S' at the end of type code)?

You can use it as a standard base board by setting its station No. to '00.' In this case, you also need to set the system definition of the loader designed f... Show Detail
- No：1531
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:50
- Category： Main unit
The SPH300EX (Type_ NP1PS-74D) has an SX bus connector. Which ports should I use when connecting the SX bus cable to the SX bus expansion base, 'IN...

The SX bus connector of the SPH300EX (Type_ NP1PS-74D) is an OUT (output) connector. When you connect SX bus equipment, connect the cable to the IN (input)... Show Detail
- No：1535
- Displayed Date：2023/04/25 19:00
- Category： Main unit
The total extension of the SX bus has exceeded 25 m. Is there anything to relay the connection?

The bus can be extended with the SX bus electrical repeater (Type_ NP2L-RP1). Up to three repeaters can be used in one system. (When three repeaters are us... Show Detail
- No：1550
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
In ST language, when I use a negative value for the base of exponentiation (such as -2.0**4.0), the calculation result is different from the case w...

In exponentiation operation, when a negative value is used for the base, the result is 0. Show Detail
- No：1551
- Displayed Date：2023/04/25 19:00
- Category： Application
There is an OPC server that supports the MICREX-SX (communication middleware, Type_ NP4N-MDLW). Is there an OPC client?

A 'client' is a device that collects data. Since the PLC is a device from which data is collected, there is no OPC client. Show Detail
- No：1553
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
I heard that the high-speed counter module (Type_ NP1F-HC2) requires a current value less than 40 mA for frequencies up to 50 kHz.

The specified current value is constant regardless of the frequency because the input impedance for the pulse input I/F is fixed. Show Detail
- No：1571
- Displayed Date：2023/04/25 19:00
- Category： Function
When I use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A), can I set software filters?

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A). Show Detail
- No：1599
- Displayed Date：2023/04/25 19:00
- Category： Function

81-90 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability