The communication specification of the remote master does not control remote devices by the station No. Therefore, you c

This problem is probably caused by the following reasons: [For SPH300/2000/3000 series] 1) The CPU mode selection switc

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). T

Since the data equalization (data copying from the operating CPU to the standby CPU) is performed after the default task

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to

If this is caused by a fluctuation in the input temperature, moving average processing shown below may improve the condi

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X

When the common memory system is used, this can be achieved by handshaking with an application using part of the link me

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

71-80 of Total 235

≪ 8 / 24page ≫

When a remote terminal master (NP1L-RM1) has been registered in 1-to-N or N-to-N mode in the system definition, can I register a remote device as '...

The communication specification of the remote master does not control remote devices by the station No. Therefore, you cannot register remote devices as 'No ... Show Detail
- No：1486
- Displayed Date：2023/04/25 19:00
- Category： Support tool
I cannot download a project to the user ROM card inserted in the CPU. What is a possible cause?

This problem is probably caused by the following reasons: [For SPH300/2000/3000 series] 1) The CPU mode selection switch is not set at the 'UROM-TERM' pos... Show Detail
- No：1528
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:47
- Category： Support tool
How long is the refresh cycle of the pulse count value data of the high-speed counter module (Type_ NP1F-HC2)?

The NP1F-HC2 constantly continues updating the pulse count value data for the SX bus I/F in a cycle of 200 ?s (fixed). The count data, however, will be refle... Show Detail
- No：1547
- Displayed Date：2023/04/25 19:00
- Category： Function
In the redundant CPU system, the cycle of the default task takes 70 ms. It takes only several microseconds with a single-CPU system. Why is such a ...

Since the data equalization (data copying from the operating CPU to the standby CPU) is performed after the default task is processed, the larger the size of... Show Detail
- No：1568
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Pulse counting is disabled on the high-speed input module (Type_ NP1X3206-A). What should I check?

Check the following points_ (1) Check the input form specified on the application program. (2) Set Enable counting to '1.' If the pulse count data regist... Show Detail
- No：1570
- Displayed Date：2023/04/25 19:00
- Category： Function
The temperature measurement value of the resistance temperature sensor (PT input) is unstable.

If this is caused by a fluctuation in the input temperature, moving average processing shown below may improve the condition. 1) Change the digital filter v... Show Detail
- No：1586
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:56
- Category： I/O
When I use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A), can I set software filters?

You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A). Show Detail
- No：1599
- Displayed Date：2023/04/25 19:00
- Category： Function
With the FL-net module (NP1L-FL1/FL2/FL3), is there any way to confirm that the data sent from the node-A have actually been received by the node-B?

When the common memory system is used, this can be achieved by handshaking with an application using part of the link memory. Without handshaking, it is not... Show Detail
- No：1638
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
With a counter module (NP1F-HC2), I use ２ counter FBs to control 2 channels. At system start-up, I set simultaneous preset operations for the 2 cha...

Check to make sure that_ (1) The channel specification (CH_SEL) is correct. (2) The FB instance names are not duplicated. (3) The preset command is given aft... Show Detail
- No：1640
- Displayed Date：2023/04/25 19:00
- Category： Function
What is the rated current value of the fuse in the power supply module (NP1S-22)? I want to know to select the circuit breaker on the primary side ...

The rated current is 3 A. Show Detail
- No：1641
- Displayed Date：2023/04/25 19:00
- Category： Main unit

71-80 of Total 235

SPH

I/O
Error

Support tool

Info & News

To Top of Page

PKSHA FAQ logo

SPH

Regional Websites

About Us

Products & Solutions

Investor Relations

Sustainability