In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determin

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a com

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redu

When downloading a project (including Patch POU), you can save the download history in your personal computer or the CP

No, it is not necessary for normal operation. The main purposes of mounting a CF card or an SD card on a CPU module are

We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of

T-link or other expansion bases cannot be added by the SX bus.

For an alarm contact output of an error of the PLC system, select an arbitrary output module in the system definitions a

You cannot mount the following I/O modules_ (1) High-speed input module NP1X3206-A, (2) High-speed output module NP1Y32

Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with inde

Skip navigation menu

Regional Websites
Americas

USA

Europe

France

Germany
Asia

China

Japan

Singapore

Hong Kong

Korea

Taiwan

India

Malaysia

Thailand

Indonesia

Philippines

Vietnam
Download documents

About Us

About Us Top
Products & Solutions

Products & Solutions Top
Investor Relations

IR Top
Sustainability

Sustainability Top

Font Size
S
M
L

GLOBAL > PLC > SPH

Latest FAQ

When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...

GLOBAL

Search by category

Keyword Search

FAQ within [ SPH ]

51-60 of Total 235

≪ 6 / 24page ≫

An address error occurs when I read a battery error of the standby CPU (CPU1) from the operating CPU (CPU0).

In a redundant system, both CPUs are identified as CPU0 and you cannot read a battery error of the standby CPU. Determine the condition of the standby CPU fr... Show Detail
- No：1572
- Displayed Date：2023/04/25 19:00
- Category： Application
Can I use a commercial LAN cable for the SX bus instead of the dedicated cable?

No, you can't. Although the connection of the sending/receiving wires of the SX bus cable is the same as that for a commercial LAN cable (cross), the dedica... Show Detail
- No：1557
- Displayed Date：2023/04/25 19:00
- Category： Accessory
A CPU module has a rotary switch (0 to F) for setting the CPU No. on its front. What CPU No. should I set?

Usually, set the CPU No. to 0. The CPU No. 0 works as a master of an SX bus system. In a multi-CPU system or a CPU redundant system which uses multiple CPU ... Show Detail
- No：1504
- Displayed Date：2023/04/25 19:00
- Category： Main unit
I use Expert (D300win). Can I check the download history to the CPU?

When downloading a project (including Patch POU), you can save the download history in your personal computer or the CPU module. [Setting procedure] ・In t... Show Detail
- No：1490
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)
The SPH300, SPH2000, and SPH3000 series CPU modules can mount a compact flash card (CF card) or an SD card. Is it necessary for normal operation?

No, it is not necessary for normal operation. The main purposes of mounting a CF card or an SD card on a CPU module are as follows. - You can write a progr... Show Detail
- No：1474
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:31
- Category： Main unit
Can I use a commercially available hub for FL-net modules?

We recommend you use an unmanaged switch, without B.S protection that is an industrial hub fulfilling the conditions of use for FL-net. * What is 'B.S'?... Show Detail
- No：1465
- Displayed Date：2023/04/25 19:00
- Updated DTM：2023/06/09 13:28
- Category： Communication (Others)
I want to expand the T-link expansion (T-link interface module Type_ NP1L-RT1) by further adding a base. Can I do this expansion by using the SX bus?

T-link or other expansion bases cannot be added by the SX bus. Show Detail
- No：1394
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
Is there an alarm output contact to use when an error occurs in the PLC system?

For an alarm contact output of an error of the PLC system, select an arbitrary output module in the system definitions and define its 0th bit as a 'system DO... Show Detail
- No：1347
- Displayed Date：2023/04/25 19:00
- Category： Main unit
Are there any I/O modules that cannot be mounted on the T-link expansion base?

You cannot mount the following I/O modules_ 　(1) High-speed input module NP1X3206-A, (2) High-speed output module NP1Y32T09P1-A, (3) Analog input module NP... Show Detail
- No：1577
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
How can I change the CPU type in an already created project?

Refer to 'Appendix 3-2 Procedure for Changing Resource (CPU type)' in the User's Manual 'Instructions' (FEH200 with index 'o' or later). Show Detail
- No：1467
- Displayed Date：2023/04/25 19:00
- Category： Support tool (D300win)