-
Products & Solutions TopProducts & Solutions
-
Products & Solutions Top
-
Drives & Controls
-
UPS & Industrial Power Supply
-
Sensors & Measurements
-
Energy Management
-
Monitoring & Control System
-
Distributions & Controls
-
Transmission & Distribution
-
Transit System
-
Semiconductors
-
Energy
-
Food and Beverage Distribution
-
Service & Equipment Upgrades
-
Solutions
-
-
IR TopInvestor Relations
Latest FAQ
- When I write parameter to LonWorks module (NP1L-LW1) using support tool for a LonWorks (NP4N-LNDF), what is the required cable?
- When I set the high-speed counter module (NP1F-HC2) to the preset operation mode of the multi-functional counter FB, the preset is disabled in the ...
- Are there any restrictions on the mounting position of the I/O modules and communication modules on the base? I'd like to place the communication m...
- When using a communication module (NP1L-RS1/RS2/RS3/RS4/RS), the FB outputs R_STS 'C0' (Hardware error detected) during receiving. In this case, ho...
- When I attempted to download a project to a CPU with user ROM card by using D300win, a message appeared saying 'Invalid loader command process!' an...
GLOBAL
Search by category
Keyword Search
FAQ within [ SPH ]
-
When the P-link module is specified as 'unimplemented' and no P-link module exists in the system, attempting to access the P-link memory using a contact, coi... Show Detail
- No：1355
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
The input/output data continue to be valid after the CPU is switched. (The previous values are retained.) Show Detail
- No：1408
- Displayed Date：2023/04/25 19:00
- Category： Application
-
It is not possible for the user to restore the factory setting. The module will have to be returned to the factory for initialization for a fee. Contact ou... Show Detail
- No：1409
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
Since the conversion accuracy after a scaling change remains within the specifications, rescaling is unnecessary. Show Detail
- No：1430
- Displayed Date：2023/04/25 19:00
- Category： I/O
-
I don't have the SX bus loop-back plug (Type_ NP8B-BP). Can I use the SX bus cable instead?
You can use it provided that the system is a single-unit system (configured with one base only). Connect the connectors at both ends of the cable to IN and ... Show Detail
- No：1543
- Displayed Date：2023/04/25 19:00
- Category： Accessory
-
Which mode does the Ethernet module (Type_ NP1L-ET1/ET2) support, half or full?
Only the NP1L-ET1 supports both modes automatically (auto negotiation). Since the NP1L-ET2 is designed for 10Base5 (coaxial), it is fixed to half duplex. Show Detail
- No：1554
- Displayed Date：2023/04/25 19:00
- Category： Communication (Ethernet)
-
This problem was probably caused by the following factors_ (1) Failed contact of the connector on the SPH, (2) Failed contact on the POD (UG), (3) Improp... Show Detail
- No：1559
- Displayed Date：2023/04/25 19:00
- Category： Communication (T-link)
-
How does the FL-net module (Type_ NP1L-FL1/FL2/FL3) clear the error history recorded in each memory?
Once an error history is generated, it is retained internally within the FL-net module and is cleared when the power is turned off and turned on again or whe... Show Detail
- No：1567
- Displayed Date：2023/04/25 19:00
- Category： Communication (Others)
-
You cannot use software filters when you use the pulse counter input function of the high-speed input module (Type_ NP1X3206-A). Show Detail
- No：1599
- Displayed Date：2023/04/25 19:00
- Category： Function
-
The rated current is 3 A. Show Detail
- No：1641
- Displayed Date：2023/04/25 19:00
- Category： Main unit
51-60 of Total 235